ASTM B199-12

    Standard Specification for Magnesium-Alloy Permanent Mold Castings


      Format Pages Price  
    PDF 6 $62.00   ADD TO CART


    1. Scope

    1.1  This specification covers magnesium alloy permanent mold casting alloys designated as shown in Table 1.

    TABLE 1 Chemical Composition LimitsA
    Note 1Analysis shall regularly be made only for the elements specifically mentioned in this table. If, however, the presence of other elements is suspected or indicated in amounts greater than the specified limits, further analysis shall be made to determine that these elements are not present in excess of the specified limits.
    Note 2The following applies to all specified limits in this table: For purposes of acceptance and rejection, an observed value or a calculated value obtained from analysis shall be rounded to the nearest unit in the last right-hand place of figures used in expressing the specified limit.

    Alloy NumberB

    Composition, %

     ASTM

    UNS

     Iron

    Magnesium

    Aluminum

    Manganese

     Zinc

    Rare Earths

    Zirconium

    Silicon

    Copper

    Nickel

    TotalC
    Other
    Impuri-
    ties

    Others
    Each

    AM100A

    M10100

     ...

    remainder

      9.3 to 10.7

    0.10–0.35

    0.30

    ...

    ...

    0.30

    0.10

    0.01

    0.30

      ...

    AZ81A

    M11810

     ...

    remainder

      7.0 to 8.1

    0.13–0.35

    0.40 to 1.0

    ...

    ...

    0.30

    0.10

    0.01

    0.30

      ...

    AZ91C

    M11914

     ...

    remainder

      8.1 to 9.3

    0.13–0.35

    0.40 to 1.0

    ...

    ...

    0.30

    0.10

    0.01

    0.30

      ...

    AZ91E

    M11919

     0.005D

    remainder

      8.1 to 9.3

    0.17–0.35

    0.40 to 1.0

    ...

    ...

    0.20

    0.015

    0.0010

    0.30

      0.01

    AZ92A

    M11920

     ...

    remainder

      8.3 to 9.7

    0.10–0.35

    1.6 to 2.4

    ...

    ...

    0.30

    0.25

    0.01

    0.30

      ...

    EQ21AE

    M18330

     ...

    remainder

      ...

    ...

    ...

    1.5 to 3.0F

    0.40 to 1.0

    ...

    0.05–0.10

    0.01

    0.30

      ...

    EZ33A

    M12330

     ...

    remainder

      ...

    ...

    2.0 to 3.1

    2.5 to 4.0

    0.50 to 1.0

    ...

    0.10

    0.01

    0.30

      ...

    QE22AG

     M18220E

     ...

    remainder

      ...

    ...

    ...

    1.8 to 2.5F

    0.40 to 1.0

    ...

    0.10

    0.01

    0.30

      ...

    A Limits are in weight percent max unless shown as a range or stated otherwise.
    B ASTM alloy designations were established in accordance with Practice B951. UNS designations were established in accordance with Practice E527.
    C  Includes listed elements for which no specific limit is shown.
    D If iron exceeds 0.005 %, the iron to manganese ratio shall not exceed 0.032.
    E Silver content for Alloy EQ21A (M18330) shall be 1.3 to 1.7 %.
    F  Rare earth elements are in the form of didymium.
    G Silver content for Alloy QE22A (M18220) shall be 2.0 to 3.0, inclusive.

    1.2 The values stated in inch-pound units are to be regarded as the standard. The SI values given in parentheses are provided for information only.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B93/B93M Specification for Magnesium Alloys in Ingot Form for Sand Castings, Permanent Mold Castings, and Die Castings

    B296 Practice for Temper Designations of Magnesium Alloys, Cast and Wrought

    B557 Test Methods for Tension Testing Wrought and Cast Aluminum- and Magnesium-Alloy Products

    B660 Practices for Packaging/Packing of Aluminum and Magnesium Products

    B661 Practice for Heat Treatment of Magnesium Alloys

    B951 Practice for Codification of Unalloyed Magnesium and Magnesium-Alloys, Cast and Wrought

    B953 Practice for Sampling Magnesium and Magnesium Alloys for Spectrochemical Analysis

    B954 Test Method for Analysis of Magnesium and Magnesium Alloys by Atomic Emission Spectrometry

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E88 Practice for Sampling Nonferrous Metals and Alloys in Cast Form for Determination of Chemical Composition

    E94 Guide for Radiographic Examination

    E155 Reference Radiographs for Inspection of Aluminum and Magnesium Castings

    E165 Practice for Liquid Penetrant Examination for General Industry

    E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)

    Federal Standards

    Fed. Std. No. 123 Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.

    Aerospace Materials Specification

    AMS 2768 Heat Treatment of Magnesium Alloy Castings


    ICS Code

    ICS Number Code 77.150.20 (Magnesium products)

    UNSPSC Code

    UNSPSC Code 31121001(Non ferrous alloy v process machined castings)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/B0199-12

    Citation Format

    ASTM B199-12, Standard Specification for Magnesium-Alloy Permanent Mold Castings, ASTM International, West Conshohocken, PA, 2012, www.astm.org

    Back to Top