ASTM B179-06
Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes
SUPERSEDED (click for Active standard)
| Format | Pages | Price | ||
 |
11 | $61.20 |  ADD TO CART |
Active (view current version of standard)
1. Scope
1.1 This specification covers commercial aluminum alloys in ingot form for remelting and molten form for the manufacture of castings. The specific gravity of these alloys does not exceed 3.0 and they are designated as shown in Table 1.
Note 1Throughout this specification the use of "ingot" in a general sense includes sow, T-bar, T-ingot, and pig.
1.2 Alloy designations are in accordance with ANSI H35.1/H35.1(M). The equivalent Unified Numbering System alloy designations are in accordance with Practice E 527.
Note 2Supplementary data pertaining to the alloys covered by this specification when used in the form of castings are given in Specifications B 26/B 26M, B 85, B 108, B 618, and B 686.
1.3 For acceptance criteria for inclusion of new aluminum and aluminum alloys in this specification, see Annex A1.
1.4 The values stated in inch-pound units are to be regarded as the standard.
This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B26/B26M Specification for Aluminum-Alloy Sand Castings
B85/B85M Specification for Aluminum-Alloy Die Castings
B108/B108M Specification for Aluminum-Alloy Permanent Mold Castings
B618/B618M Specification for Aluminum-Alloy Investment Castings
B666/B666M Practice for Identification Marking of Aluminum and Magnesium Products
B686/B686M Specification for Aluminum Alloy Castings, High-Strength
B955/B955M Specification for Aluminum-Alloy Centrifugal Castings
B969 Specification for Aluminum-Alloy Castings Produced by the Squeeze Casting, Thixocast and Rheocast Semi-Solid Casting Processes
B985 Practice for Sampling Aluminum Ingots, Billets, Castings and Finished or Semi-Finished Wrought Aluminum Products for Compositional Analysis
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
E607 Test Method for Atomic Emission Spectrometric Analysis Aluminum Alloys by the Point to Plane Technique Nitrogen Atmosphere
E716 Practices for Sampling and Sample Preparation of Aluminum and Aluminum Alloys for Determination of Chemical Composition by Spectrochemical Analysis
E1251 Test Method for Analysis of Aluminum and Aluminum Alloys by Spark Atomic Emission Spectrometry
ANSI Standard
H35.1/H35.1(M) American National Standard Alloy and Temper Designation Systems for Aluminum Available from Aluminum Association, Inc., 1525 Wilson Blvd., Suite 600, Arlington, VA 22209, http://www.aluminum.org.Aluminum Associations Standard
Designations and Chemical Composition Limits for A (The Pink Sheets)ICS Code
ICS Number Code 77.120.10 (Aluminium and aluminium alloys)
UNSPSC Code
UNSPSC Code 30265202(Aluminum ingot)
Referencing This Standard
| Link Here | |||
| Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/B0179-06
Citation Format
ASTM B179-06, Standard Specification for Aluminum Alloys in Ingot and Molten Forms for Castings from All Casting Processes, ASTM International, West Conshohocken, PA, 2006, www.astm.org
Back to Top