Standard Historical Last Updated: Aug 16, 2017 Track Document
ASTM A999/A999M-98

Standard Specification for General Requirements for Alloy and Stainless Steel Pipe

Standard Specification for General Requirements for Alloy and Stainless Steel Pipe A0999_A0999M-98 ASTM|A0999_A0999M-98|en-US Standard Specification for General Requirements for Alloy and Stainless Steel Pipe Standard new BOS Vol. 01.01 Committee A01
$ 75.00 In stock

Scope

1.1 This specification covers a group of general requirements that, unless otherwise specified in an individual specification, shall apply to the ASTM product specifications noted below.

1.2 In the case of conflict between a requirement of a product specification and a requirement of this specification, the product specification shall prevail. In the case of conflict between a requirement of the product specification or a requirement of this specification and a more stringent requirement of the purchase order, the purchase order shall prevail.

Title of SpecificationASTM Designation
Seamless and Welded Austenitic Stainless Steel PipeA 312/A 312M
Seamless and Welded Steel Pipe for Low-Temperature ServiceA 333/A 333M
Seamless Ferritic Alloy-Steel Pipe for High Temperature ServiceA 335/A 335M
Electric-Fusion-Welded Austenitic Chromium-Nickel Alloy Steel Pipe for High-Temperature ServiceA 358/A 358M
Carbon and Ferritic Alloy Steel Forged and Bored Pipe for High-Temperature Service A 369/A 369M
Seamless Austenitic Steel Pipe for Use With High Temperature Central-Station Service A 376/A 376M
Welded Large Diameter Austenitic Steel Pipe for Corrosive or High-Temperature ServiceA 409/A 409M
Welded, Unannealed Austenitic Stainless Steel Tubular ProductsA 778
Seamless and Welded Ferritic/Austenitic Stainless Steel PipeA 790/A 790M
Single- or Double-Welded Austenitic Stainless Steel PipeA 813/A 813M
Cold-Worked Welded Austenitic Stainless Steel PipeA 814/A 814M
Ferritic/Austenitic (Duplex) Stainless Steel Pipe Electric Fusion Welded with Addition of Filler MetalA 928
Spray-Formed Seamless Austenitic Stainless Steel PipeA 943
Spray-Formed Seamless Ferritic/Austenitic Stainless Steel PipeA 949
Austenitic Chromium-Nickel-Silicon Alloy Steel Seamless and Welded Pipe A 954

1.3 The values stated in either inch-pound units or SI units are to be regarded separately as standard. With the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification. The inch-pound units shall apply unless the "M" designation (SI) of the product specification is specified in the order.

Note 1--The dimensionless designator NPS (nominal pipe size) is used in this standard for such traditional terms as "nominal diameter," "size,"" nominal bore," and "nominal size".

1.4 The following precautionary statement pertains only to the test method portion, Section 21, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Price:
Contact Sales
Related
Reprints and Permissions
Reprints and copyright permissions can be requested through the
Copyright Clearance Center
Details
Book of Standards Volume: 01.01
Developed by Subcommittee: A01.10
Pages: 10
DOI: 10.1520/A0999_A0999M-98
ICS Code: 23.040.10