ASTM A933/A933M-10

    Standard Specification for Vinyl-Coated Steel Wire and Welded Wire Reinforcement

      Format Pages Price  
    PDF 11 $62.40   ADD TO CART

    1. Scope

    1.1 This specification covers plain and deformed steel wire and plain and deformed steel welded wire reinforcement with protective vinyl (polyvinyl chloride, or polyvinyl chloride powder compound) coating. A Class A minimum coating thickness is required for wire and welded wire reinforcement intended for use in concrete and masonry. A Class B minimum coating thickness is required for wire and welded wire reinforcement intended for use in mechanically stabilized earth applications.

    1.2 Other thermoplastic organic coatings may be used provided they meet the requirements of this specification.

    Note 1—The coating applicator is identified throughout this specification as the manufacturer.

    1.3 Requirements for coatings are contained in Annex A1.

    1.4 Requirements for patching materials are contained in Annex A2.

    1.5 The text of this specification contains notes or footnotes, or both, that provide explanatory material. Such notes and footnotes, excluding those in tables or figures, do not contain any mandatory requirements.

    1.6 This specification is applicable for orders in either inch-pound units (as Specification A933) or in SI units [as Specification A933M].

    1.7 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A775/A775M Specification for Epoxy-Coated Steel Reinforcing Bars

    A884/A884M Specification for Epoxy-Coated Steel Wire and Welded Wire Reinforcement

    A1064/A1064M Specification for Carbon-Steel Wire and Welded Wire Reinforcement, Plain and Deformed, for Concrete

    B117 Practice for Operating Salt Spray (Fog) Apparatus

    D374 Test Methods for Thickness of Solid Electrical Insulation

    D2240 Test Method for Rubber Property--Durometer Hardness

    D2967 Test Method for Corner Coverage of Powder Coatings

    D4060 Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser

    G8 Test Methods for Cathodic Disbonding of Pipeline Coatings

    G12 Test Method for Nondestructive Measurement of Film Thickness of Pipeline Coatings on Steel

    G14 Test Method for Impact Resistance of Pipeline Coatings (Falling Weight Test)

    G20 Test Method for Chemical Resistance of Pipeline Coatings

    National Association of Corrosion Engineers Standards

    RP-287-87 Field Measurement of Surface Profile of Abrasive Blast Cleaned Steel Surface Using a Replica Tape

    TM-01-70 Visual Standard for Surfaces of New Steel Air Blast Cleaned with Sand Abrasive (NACE No. 2)

    TM-01-75 Visual Standard for Surfaces of New Steel Centrifugally Blast Cleaned with Steel Shot or Steel Grit (NACE No. 2)

    Steel Structures Painting Council Specifications

    SSPC-PA2 Measurement of Dry Coating Thickness with Magnetic Gages

    SSPC-SP 10 Near-White Blast Cleaning

    SSPC-Vis 1 Pictorial Surface Preparation Standards for Painting Steel Surfaces

    SSPC-Vis 2 Standard Methods of Evaluating Degree of Rusting on Painted Steel Surfaces

    ICS Code

    ICS Number Code 77.140.15 (Steels for reinforcement of concrete)

    UNSPSC Code

    UNSPSC Code 30111900(Concrete reinforcement hardware)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A0933_A0933M-10

    Citation Format

    ASTM A933 / A933M-10, Standard Specification for Vinyl-Coated Steel Wire and Welded Wire Reinforcement, ASTM International, West Conshohocken, PA, 2010,

    Back to Top