SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|8||$54.00||  ADD TO CART|
1.1 This specification covers two general classes, WP and CR, of wrought ferritic, ferritic/austenitic, and martensitic stainless steel fittings of seamless and welded construction covered by the latest revision of Specification A960/A960M. Fittings differing from these standards may be furnished in accordance with Supplementary Requirement S58 of Specification A960/A960M.
1.1.1 Class WP fittings are subdivided into four subclasses: Classes WP-S, WP-W, WP-WX, and WP-WU. They are manufactured to the requirements of Specification A960/A960M, and they shall have pressure ratings compatible with 12.2. Class WP-S fittings are those manufactured from seamless product by a seamless method of manufacture (marked with class symbol WP-S); Class WP-W fittings are those which contain welds where the fitting fabrication or construction welds have been radiographed (marked with class symbol WP-W); and Class WP-WX fittings are those which contain welds where all welds have been radiographed (marked with class symbol WP-WX); and Class WP-WU fittings are those which contain welds where all welds have been ultrasonically tested (marked with class symbol WP-WU).
1.1.2 Class CR fittings are those manufactured to the requirements of MSS SP-43, and they shall have pressure ratings compatible with 12.3.
1.2 This specification does not apply to cast fittings.
1.3 Optional supplementary requirements are provided. When desired, one or more of these may be specified in the order.
1.4 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable “M” specification designation [SI units], the material shall be furnished to inch-pound units.
1.5 The values stated in either SI units or inch-pound units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels
A388/A388M Practice for Ultrasonic Examination of Steel Forgings
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
A763 Practices for Detecting Susceptibility to Intergranular Attack in Ferritic Stainless Steels
A923 Test Methods for Detecting Detrimental Intermetallic Phase in Duplex Austenitic/Ferritic Stainless Steels
A960/A960M Specification for Common Requirements for Wrought Steel Piping Fittings
E165 Practice for Liquid Penetrant Examination for General Industry
ASME StandardsB16.11 Forged Fittings, Socket-Welding and Threaded B16.9
MSS StandardsMSS SP-43 MSS SP-79 Socket-Welding Reducer Inserts MSS SP-83 Steel Pipe Unions, Socket-Welding and Threaded MSS SP-95 MSS SP-97 Integrally Reinforced Forged Branch Outlet FittingsSocket Welding, Threaded and Buttwelding Ends
ICS Number Code 23.040.40 (Metal fittings)
UNSPSC Code 40171600(Industrial pipe and piping)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM A815 / A815M-10, Standard Specification for Wrought Ferritic, Ferritic/Austenitic, and Martensitic Stainless Steel Piping Fittings, ASTM International, West Conshohocken, PA, 2010, www.astm.orgBack to Top