SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|4||$48.00||  ADD TO CART|
1.1 This specification covers five grades of as-welded, wrought austenitic stainless steel fittings for low-pressure piping and intended for low and moderate temperatures and general corrosive service. Users should note that certain corrosive conditions may restrict the use of one or more grades. For applications requiring a product that requires heat treatment or full pressure rating, refer to Specification A 403/A 403M. The term "fittings" applies to butt and socket welding parts such as 45 and 90 elbows, tees, reducers, wyes, laterals, crosses, and stub ends.
1.2 This specification covers as-welded fittings 3 through 48 in. [75 through 1225 mm] in outside diameter and in nominal wall thicknesses 0.062 through 0.500 in. [1.6 through 12.7 mm]. and list the common diameters and nominal thicknesses of fittings in this specification.
1.3 This specification does not apply to cast fittings. Cast austenitic steel fittings are covered by Specification A 351/A 351M.
1.4 Optional supplementary requirements are provided for fittings where a greater degree of examination is desired. These supplementary requirements call for additional tests. When desired, one or more of these may be specified in the order.
1.5 This specification is expressed in both inch-pound units and in SI units. However, unless the order specifies the applicable "M" specification designation (SI units), the material shall be furnished to inch-pound units.
1.6 The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications
A351/A351M Specification for Castings, Austenitic, for Pressure-Containing Parts
A403/A403M Specification for Wrought Austenitic Stainless Steel Piping Fittings
A960/A960M Specification for Common Requirements for Wrought Steel Piping Fittings
E527 Practice for Numbering Metals and Alloys in the Unified Numbering System (UNS)
ASME StandardSection IX ASME Boiler and Pressure Vessel Code Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Two Park Ave., New York, NY 10016-5990, http://www.asme.org.
AWS StandardsA5.4 Corrosion-Resisting Chromium and Chromium-Nickel Steel Covered Welding Electrodes Available from American Welding Society (AWS), 550 NW LeJeune Rd., Miami, FL 33126, http://www.aws.org. A5.9 Corrosion-Resisting Chromium and Chromium-Nickel Steel Welding Rods and Bare Electrodes
SAE StandardJ1086 Unified Numbering System for Metals and Alloys Available from Society of Automotive Engineers (SAE), 400 Commonwealth Dr., Warrendale, PA 15096-0001, http://www.sae.org.
ICS Number Code 77.140.20 (Steels of high quality)
UNSPSC Code 40170000(Pipe piping and pipe fittings)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM A774 / A774M-06, Standard Specification for As-Welded Wrought Austenitic Stainless Steel Fittings for General Corrosive Service at Low and Moderate Temperatures, ASTM International, West Conshohocken, PA, 2006, www.astm.orgBack to Top