SUPERSEDED (click for Active standard)
| ||Format||Pages||Price|| |
|8||$54.00||  ADD TO CART|
1.1 This specification covers chemical and mechanical requirements for eight grades of carbon and alloy steel nuts for general structural and mechanical uses on bolts, studs, and other externally threaded parts. Note 1 - See for guidance on suitable application of nut grades.
1.2 The requirements for any grade of nut may, at the supplier's option, and with notice to the purchaser, be fulfilled by furnishing nuts of one of the stronger grades specified herein unless such substitution is barred in the inquiry and purchase order.
1.3 Grades C3 and DH3 nuts have atmospheric corrosion resistance and weathering characteristics comparable to that of the steels covered in Specifications A 242/A 242M, A 588/A 588M, and A 709/A 709M. The atmospheric corrosion resistance of these steels is substantially better than that of carbon steel with or without copper addition (see ). When properly exposed to the atmosphere, these steels can be used bare (uncoated) for many applications. Note 2 - A complete metric companion to Specification A 563 has been developed-A 563M; therefore, no metric equivalents are presented in this specification.<>
1.4 Terms used in this specification are defined in Terminology F 1789 unless otherwise defined herein.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
A194/A194M Specification for Carbon Steel, Alloy Steel, and Stainless Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both
A242/A242M Specification for High-Strength Low-Alloy Structural Steel
A307 Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSI Tensile Strength
A325 Specification for Structural Bolts, Steel, Heat Treated, 120/105 ksi Minimum Tensile Strength
A354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners
A394 Specification for Steel Transmission Tower Bolts, Zinc-Coated and Bare
A449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use
A490 Specification for Structural Bolts, Alloy Steel, Heat Treated, 150 ksi Minimum Tensile Strength
A563M Specification for Carbon and Alloy Steel Nuts (Metric)
A588/A588M Specification for High-Strength Low-Alloy Structural Steel, up to 50 ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion Resistance
A687 Specification for High-Strength Nonheaded Steel Bolts and Studs
A709/A709M Specification for Structural Steel for Bridges
A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products
B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel
D3951 Practice for Commercial Packaging
F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric) F0606_F0606M
F812/F812M Specification for Surface Discontinuities of Nuts, Inch and Metric Series
F1789 Terminology for F16 Mechanical Fasteners
F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners
G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels
ICS Number Code 21.060.20 (Nuts)
UNSPSC Code 31161700(Nuts); 31161600(Bolts)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM A563-07, Standard Specification for Carbons and Alloy Steel Nuts, ASTM International, West Conshohocken, PA, 2007, www.astm.orgBack to Top