ASTM A449-04b

    Specification for Hex Cap Screws, Bolts, and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

      Format Pages Price  
    PDF 7 $62.00   ADD TO CART

    1. Scope

    1.1 This specification covers the chemical and mechanical requirements for two types of quenched and tempered steel bolts and studs for general applications where high strength is required.

    1.2 The two types of bolts covered in this specification are:

    1.2.1 Type 1—Medium-carbon steel bolts and studs furnished in nominal diameters of 1/4 to 3 in., inclusive.

    1.2.2 Type 2—Low-carbon martensite or medium-carbon martensite steel bolts and studs furnished in nominal diameters of 1/4to 1 in., inclusive.

    1.3 The bolts and studs shall be Type 1, Type 2, or Type 1 or 2 at manufacturer's option, as specified by the purchaser. When a type is not specified, Type 1 shall be furnished. When elevated temperature applications are involved, Type 1 shall be specified by the purchaser on the order.

    1.4 Suitable nuts are covered in Specification A 563. Unless otherwise specified, the grade and style of nut shall be as follows:

    Nuts of other grades and styles having specified proof load stresses (Specification A 563, Table 3) greater than the specified grade and style of nut are suitable.

    Fastener Size and Surface Finish Nut Grade and Style
    1/4 to 11/2 in., plain (or with a coating of insufficient thickness to require over-tapped nuts) B, hex
    Over 11/2 to 3 in., plain (or with a coating of insuffi-cient thickness to require over-tapped nuts) A, heavy hex
    1/4 to 3 in., zinc-coated (or with a coating thicknessrequiring over-tapped nuts) DH, heavy hex

    1.5 Unless otherwise specified, washers ordered with bolts shall be furnished to the requirements of Specification F 436.

    1.6 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are provided for information purposes only.

    1.7 Terms used in this specification are defined in Terminology F 1789 unless otherwise defined herein.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A563 Specification for Carbon and Alloy Steel Nuts

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    B695 Specification for Coatings of Zinc Mechanically Deposited on Iron and Steel

    F436/F436M Specification for Hardened Steel Washers Inch and Metric Dimensions

    F606/F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets

    F788/F788M Specification for Surface Discontinuities of Bolts, Screws, Studs, and Rivets, Inch and Metric Series

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F1789 Terminology for F16 Mechanical Fasteners

    F2329 Specification for Zinc Coating, Hot-Dip, Requirements for Application to Carbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded Fasteners

    G101 Guide for Estimating the Atmospheric Corrosion Resistance of Low-Alloy Steels

    ASME Standards

    B18.2.1 Square and Hex Bolts and Screws

    ICS Code

    ICS Number Code 21.060.10 (Bolts, screws, studs)

    UNSPSC Code

    UNSPSC Code 31160000(Hardware)

    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/A0449-04B

    Citation Format

    ASTM A449-04b, Specification for Hex Cap Screws, Bolts, and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use, ASTM International, West Conshohocken, PA, 2004,

    Back to Top