SUPERSEDED (click for Active standard)
  | Format | Pages | Price |   |
![]() |
49 | $97.00 | ![]() |
Active (view current version of standard)
Work Item(s) - proposed revisions of this standard
1. Scope
1.1 These test methods cover procedures and definitions for the mechanical testing of wrought and cast steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.
1.2 The following mechanical tests are described:
Sections | |
Tension | 5 to 13 |
Bend | 14 |
Hardness | 15 |
Brinell | 16 |
Rockwell | 17 |
Portable | 18 |
Impact | 19 to 28 |
Keywords | 29 |
1.3 Annexes covering details peculiar to certain products are appended to these test methods as follows:
Annex | |
Bar Products | A1.1 |
Tubular Products | Annex A2 |
Fasteners | Annex A3 |
Round Wire Products | Annex A4 |
Significance of Notched-Bar Impact Testing | Annex A5 |
Converting Percentage Elongation of Round Specimens to Equivalents for Flat Specimens | Annex A6 |
Testing Multi-Wire Strand | Annex A7 |
Rounding of Test Data | Annex A8 |
Methods for Testing Steel Reinforcing Bars | Annex A9 |
Procedure for Use and Control of Heat-Cycle Simulation | Annex A10 |
1.4 The values stated in inch-pound units are to be regarded as the standard.
1.5 When this document is referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gage lengths of 2 or 8 in. may be reported in SI unit gage lengths of 50 or 200 mm, respectively, as applicable. Conversely, when this document is referenced in an inch-pound product specification, the yield and tensile values may be determined in SI units then converted into inch-pound units. The elongation determined in SI unit gage lengths of 50 or 200 mm may be reported in inch-pound gage lengths of 2 or 8 in., respectively, as applicable.
1.6 Attention is directed to Practices A 880 and E 1595 when there may be a need for information on criteria for evaluation of testing laboratories.
1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
A623 Specification for Tin Mill Products, General Requirements
A623M Specification for Tin Mill Products, General Requirements [Metric]
A833 Test Method for Indentation Hardness of Metallic Materials by Comparison Hardness Testers
A941 Terminology Relating to Steel, Stainless Steel, Related Alloys, and Ferroalloys
A1038 Test Method for Portable Hardness Testing by the Ultrasonic Contact Impedance Method
A1058 Test Methods for Mechanical Testing of Steel ProductsMetric
A1061/A1061M Test Methods for Testing Multi-Wire Steel Prestressing Strand
E4 Practices for Force Verification of Testing Machines
E6 Terminology Relating to Methods of Mechanical Testing
E8/E8M Test Methods for Tension Testing of Metallic Materials
E10 Test Method for Brinell Hardness of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E23 Test Methods for Notched Bar Impact Testing of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E83 Practice for Verification and Classification of Extensometer Systems
E110 Test Method for Rockwell and Brinell Hardness of Metallic Materials by Portable Hardness Testers
E190 Test Method for Guided Bend Test for Ductility of Welds
E290 Test Methods for Bend Testing of Material for Ductility
ISO Standard
ISO/IEC 17025ICS Code
ICS Number Code 77.040.10 (Mechanical testing of metals); 77.140.01 (Iron and steel products in general)
UNSPSC Code
UNSPSC Code 11101704(Steel); 41114614(Metal testing instruments)
Link Here | |||
Link to Active (This link will always route to the current Active version of the standard.) | |||
DOI: 10.1520/A0370-03A
Citation Format
ASTM A370-03a, Standard Test Methods and Definitions for Mechanical Testing of Steel Products, ASTM International, West Conshohocken, PA, 2003, www.astm.org
Back to Top