ASTM Volume 05.04, March 2021

    Petroleum Products, Liquid Fuels, and Lubricants (IV): D7412 – D8128

    Table of Contents

    D7412-18 Standard Test Method for Condition Monitoring of Phosphate Antiwear Additives in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry

    D7414-18 Standard Test Method for Condition Monitoring of Oxidation in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry

    D7415-18 Standard Test Method for Condition Monitoring of Sulfate By-Products in In-Service Petroleum and Hydrocarbon Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry

    D7416-09(2020) Standard Practice for Analysis of In-Service Lubricants Using a Particular Five-Part (Dielectric Permittivity, Time-Resolved Dielectric Permittivity with Switching Magnetic Fields, Laser Particle Counter, Microscopic Debris Analysis, and Orbital Viscometer) Integrated Tester

    D7417-17 Standard Test Method for Analysis of In-Service Lubricants Using Particular Four-Part Integrated Tester (Atomic Emission Spectroscopy, Infrared Spectroscopy, Viscosity, and Laser Particle Counter)

    D7418-20 Standard Practice for Set-Up and Operation of Fourier Transform Infrared (FT-IR) Spectrometers for In-Service Oil Condition Monitoring

    D7419-18 Standard Test Method for Determination of Total Aromatics and Total Saturates in Lube Basestocks by High Performance Liquid Chromatography (HPLC) with Refractive Index Detection

    D7420-18 Standard Test Method for Determining Tribomechanical Properties of Grease Lubricated Plastic Socket Suspension Joints Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7421-19 Standard Test Method for Determining Extreme Pressure Properties of Lubricating Oils Using High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7422-19 Standard Test Method for Evaluation of Diesel Engine Oils in T-12 Exhaust Gas Recirculation Diesel Engine

    D7423-17 Standard Test Method for Determination of Oxygenates in C2, C3, C4, and C5 Hydrocarbon Matrices by Gas Chromatography and Flame Ionization Detection

    D7450-19 Standard Specification for Performance of Rear Axle Gear Lubricants Intended for API Category GL-5 Service

    D7451-20 Standard Test Method for Water Separation Properties of Light and Middle Distillate, and Compression and Spark-Ignition Engine Fuels

    D7452-19 Standard Test Method for Evaluation of the Load Carrying Properties of Lubricants Used for Final Drive Axles, Under Conditions of High Speed and Shock Loading

    D7453-18 Standard Practice for Sampling of Petroleum Products for Analysis by Process Stream Analyzers and for Process Stream Analyzer System Validation

    D7454-19 Standard Test Method for Determination of Vibrated Bulk Density of Calcined Petroleum Coke using a Semi-Automated Apparatus

    D7455-19 Standard Practice for Sample Preparation of Petroleum and Lubricant Products for Elemental Analysis

    D7463-21 Standard Test Method for Adenosine Triphosphate (ATP) Content of Microorganisms in Fuel, Fuel/Water Mixtures, and Fuel Associated Water

    D7464-20 Standard Practice for Manual Sampling of Liquid Fuels, Associated Materials and Fuel System Components for Microbiological Testing

    D7467-20a Standard Specification for Diesel Fuel Oil, Biodiesel Blend (B6 to B20)

    D7468-21 Standard Test Method for Cummins ISM Test

    D7482-17 Standard Practice for Sampling, Storage, and Handling of Hydrocarbons for Mercury Analysis

    D7483-21 Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Oscillating Piston Viscometer

    D7484-21a Standard Test Method for Evaluation of Automotive Engine Oils for Valve-Train Wear Performance in Cummins ISB Medium-Duty Diesel Engine

    D7500-15(2019) Standard Test Method for Determination of Boiling Range Distribution of Distillates and Lubricating Base Oils—in Boiling Range from 100 °C to 735 °C by Gas Chromatography

    D7501-18a Standard Test Method for Determination of Fuel Filter Blocking Potential of Biodiesel (B100) Blend Stock by Cold Soak Filtration Test (CSFT)

    D7524-20 Standard Test Method for Determination of Static Dissipater Additives (SDA) in Aviation Turbine Fuel and Middle Distillate Fuels—High Performance Liquid Chromatograph (HPLC) Method

    D7525-14(2019)e1 Standard Test Method for Oxidation Stability of Spark Ignition Fuel—Rapid Small Scale Oxidation Test (RSSOT)

    D7527-10(2018) Standard Test Method for Measurement of Antioxidant Content in Lubricating Greases by Linear Sweep Voltammetry

    D7528-21 Standard Test Method for Bench Oxidation of Engine Oils by ROBO Apparatus

    D7544-12(2017) Standard Specification for Pyrolysis Liquid Biofuel

    D7545-14(2019)e1 Standard Test Method for Oxidation Stability of Middle Distillate Fuels—Rapid Small Scale Oxidation Test (RSSOT)

    D7546-15 Standard Test Method for Determination of Moisture in New and In-Service Lubricating Oils and Additives by Relative Humidity Sensor

    D7547-21 Standard Specification for Hydrocarbon Unleaded Aviation Gasoline

    D7548-16a Standard Test Method for Determination of Accelerated Iron Corrosion in Petroleum Products

    D7549-21 Standard Test Method for Evaluation of Heavy-Duty Engine Oils under High Output Conditions—Caterpillar C13 Test Procedure

    D7563-10(2016) Standard Test Method for Evaluation of the Ability of Engine Oil to Emulsify Water and Simulated Ed85 Fuel

    D7566-21 Standard Specification for Aviation Turbine Fuel Containing Synthesized Hydrocarbons

    D7576-16 Standard Test Method for Determination of Benzene and Total Aromatics in Denatured Fuel Ethanol by Gas Chromatography

    D7577-12(2021) Standard Test Method for Determining the Accelerated Iron Corrosion Rating of Denatured Fuel Ethanol and Ethanol Fuel Blends

    D7578-20 Standard Guide for Calibration Requirements for Elemental Analysis of Petroleum Products and Lubricants

    D7579-09(2019) Standard Test Method for Pyrolysis Solids Content in Pyrolysis Liquids by Filtration of Solids in Methanol

    D7589-16 Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VID Spark Ignition Engine

    D7590-09(2014) Standard Guide for Measurement of Remaining Primary Antioxidant Content In In-Service Industrial Lubricating Oils by Linear Sweep Voltammetry

    D7591-12(2017) Standard Test Method for Determination of Free and Total Glycerin in Biodiesel Blends by Anion Exchange Chromatography

    D7593-14 Standard Test Method for Determination of Fuel Dilution for In-Service Engine Oils by Gas Chromatography

    D7594-19 Standard Test Method for Determining Fretting Wear Resistance of Lubricating Greases Under High Hertzian Contact Pressures Using a High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7596-14 Standard Test Method for Automatic Particle Counting and Particle Shape Classification of Oils Using a Direct Imaging Integrated Tester

    D7603-13 Standard Test Method for Determination of Storage Stability and Compatibility in Automotive Gear Oils

    D7618-13(2021) Standard Specification for Ethyl Tertiary-Butyl Ether (ETBE) for Blending with Aviation Spark-Ignition Engine Fuel

    D7619-17 Standard Test Method for Sizing and Counting Particles in Light and Middle Distillate Fuels, by Automatic Particle Counter

    D7620-10(2020) Standard Test Method for Determination of Total Sulfur in Liquid Hydrocarbon Based Fuels by Continuous Injection, Air Oxidation and Ultraviolet Fluorescence Detection

    D7621-16(2021) Standard Test Method for Determination of Hydrogen Sulfide in Fuel Oils by Rapid Liquid Phase Extraction

    D7622-20 Standard Test Method for Total Mercury in Crude Oil Using Combustion and Direct Cold Vapor Atomic Absorption Method with Zeeman Background Correction

    D7623-20 Standard Test Method for Total Mercury in Crude Oil Using Combustion-Gold Amalgamation and Cold Vapor Atomic Absorption Method

    D7624-18 Standard Test Method for Condition Monitoring of Nitration in In-Service Petroleum and Hydrocarbon-Based Lubricants by Trend Analysis Using Fourier Transform Infrared (FT-IR) Spectrometry

    D7646-10(2019) Standard Test Method for Determination of Cooling Characteristics of Aqueous Polymer Quenchants for Aluminum Alloys by Cooling Curve Analysis

    D7647-10(2018) Standard Test Method for Automatic Particle Counting of Lubricating and Hydraulic Fluids Using Dilution Techniques to Eliminate the Contribution of Water and Interfering Soft Particles by Light Extinction

    D7665-17 Standard Guide for Evaluation of Biodegradable Heat Transfer Fluids

    D7666-12(2019) Standard Specification for Triglyceride Burner Fuel

    D7667-10(2015) Standard Test Method for Determination of Corrosiveness to Silver by Automotive Spark-Ignition Engine Fuel—Thin Silver Strip Method

    D7669-20 Standard Guide for Practical Lubricant Condition Data Trend Analysis

    D7670-10(2017) Standard Practice for Processing In-service Fluid Samples for Particulate Contamination Analysis Using Membrane Filters

    D7671-10(2021) Standard Test Method for Corrosiveness to Silver by Automotive Spark–Ignition Engine Fuel–Silver Strip Method

    D7683-21 Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Small Test Jar Method)

    D7684-11(2020) Standard Guide for Microscopic Characterization of Particles from In-Service Lubricants

    D7685-11(2016) Standard Practice for In-Line, Full Flow, Inductive Sensor for Ferromagnetic and Non-ferromagnetic Wear Debris Determination and Diagnostics for Aero-Derivative and Aircraft Gas Turbine Engine Bearings

    D7686-19 Standard Test Method for Field-Based Condition Monitoring of Soot in In-Service Lubricants Using a Fixed-Filter Infrared (IR) Instrument

    D7687-21 Standard Test Method for Measurement of Cellular Adenosine Triphosphate in Fuel and Fuel-associated Water With Sample Concentration by Filtration

    D7688-18 Standard Test Method for Evaluating Lubricity of Diesel Fuels by the High-Frequency Reciprocating Rig (HFRR) by Visual Observation

    D7689-21 Standard Test Method for Cloud Point of Petroleum Products and Liquid Fuels (Mini Method)

    D7690-11(2017) Standard Practice for Microscopic Characterization of Particles from In-Service Lubricants by Analytical Ferrography

    D7691-16 Standard Test Method for Multielement Analysis of Crude Oils Using Inductively Coupled Plasma Atomic Emission Spectrometry (ICP-AES)

    D7717-11(2017) Standard Practice for Preparing Volumetric Blends of Denatured Fuel Ethanol and Gasoline Blendstocks for Laboratory Analysis

    D7718-11(2019) Standard Practice for Obtaining In-Service Samples of Lubricating Grease

    D7719-21a Standard Specification for High Aromatic Content Unleaded Hydrocarbon Aviation Gasoline Test Fuel

    D7720-11(2017) Standard Guide for Statistically Evaluating Measurand Alarm Limits when Using Oil Analysis to Monitor Equipment and Oil for Fitness and Contamination

    D7721-17 Standard Practice for Determining the Effect of Fluid Selection on Hydraulic System or Component Efficiency

    D7739-11(2020) Standard Practice for Thermal Oxidative Stability Measurement via Quartz Crystal Microbalance

    D7740-20 Standard Practice for Optimization, Calibration, and Validation of Atomic Absorption Spectrometry for Metal Analysis of Petroleum Products and Lubricants

    D7751-16(2021) Standard Test Method for Determination of Additive Elements in Lubricating Oils by EDXRF Analysis

    D7752-18 Standard Practice for Evaluating Compatibility of Mixtures of Hydraulic Fluids

    D7753-12(2020) Standard Test Method for Hydrocarbon Types and Benzene in Light Petroleum Distillates by Gas Chromatography

    D7754-19 Standard Test Method for Determination of Trace Oxygenates in Automotive Spark-Ignition Engine Fuel by Multidimensional Gas Chromatography

    D7755-11(2017) Standard Practice for Determining the Wear Volume on Standard Test Pieces Used by High-Frequency, Linear-Oscillation (SRV) Test Machine

    D7756-19 Standard Test Method for Residues in Liquefied Petroleum (LP) Gases by Gas Chromatography with Liquid, On-Column Injection

    D7757-17 Standard Test Method for Silicon in Gasoline and Related Products by Monochromatic Wavelength Dispersive X-ray Fluorescence Spectrometry

    D7777-13(2018)e1 Standard Test Method for Density, Relative Density, or API Gravity of Liquid Petroleum by Portable Digital Density Meter

    D7778-15 Standard Guide for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

    D7794-21 Standard Practice for Blending Mid-Level Ethanol Fuel Blends for Flexible-Fuel Vehicles with Automotive Spark-Ignition Engines

    D7795-15 Standard Test Method for Acidity in Ethanol and Ethanol Blends by Titration

    D7796-17 Standard Test Method for Analysis of Ethyl tert-Butyl Ether (ETBE) by Gas Chromatography

    D7797-18 Standard Test Method for Determination of the Fatty Acid Methyl Esters Content of Aviation Turbine Fuel Using Flow Analysis by Fourier Transform Infrared Spectroscopy—Rapid Screening Method

    D7798-20 Standard Test Method for Boiling Range Distribution of Petroleum Distillates with Final Boiling Points up to 538 °C by Ultra Fast Gas Chromatography (UF GC)

    D7806-20 Standard Test Method for Determination of Biodiesel (Fatty Acid Methyl Ester) and Triglyceride Content in Diesel Fuel Oil Using Mid-Infrared Spectroscopy (FTIR Transmission Method)

    D7807-20 Standard Test Method for Determination of Boiling Range Distribution of Hydrocarbon and Sulfur Components of Petroleum Distillates by Gas Chromatography and Chemiluminescence Detection

    D7808-18 Standard Practice for Determining the Site Precision of a Process Stream Analyzer on Process Stream Material

    D7825-18 Standard Practice for Generating a Process Stream Property Value through Application of a Process Stream Analyzer

    D7826-20a Standard Guide for Evaluation of New Aviation Gasolines and New Aviation Gasoline Additives

    D7827-19 Standard Test Method for Measuring n-Heptane Induced Phase Separation of Asphaltene from Heavy Fuel Oils as Separability Number by an Optical Device

    D7829-13(2018) Standard Guide for Sediment and Water Determination in Crude Oil

    D7843-21 Standard Test Method for Measurement of Lubricant Generated Insoluble Color Bodies in In-Service Turbine Oils using Membrane Patch Colorimetry

    D7844-20 Standard Test Method for Condition Monitoring of Soot in In-Service Lubricants by Trend Analysis using Fourier Transform Infrared (FT-IR) Spectrometry

    D7845-20 Standard Test Method for Determination of Chemical Species in Marine Fuel Oil by Multidimensional Gas Chromatography/Mass Spectrometry

    D7847-17 Standard Guide for Interlaboratory Studies for Microbiological Test Methods

    D7861-14(2019) Standard Test Method for Determination of Fatty Acid Methyl Esters (FAME) in Diesel Fuel by Linear Variable Filter (LVF) Array Based Mid-Infrared Spectroscopy

    D7862-21 Standard Specification for Butanol for Blending with Gasoline for Use as Automotive Spark-Ignition Engine Fuel

    D7863-17 Standard Guide for Evaluation of Convective Heat Transfer Coefficient of Liquids

    D7872-13(2018) Standard Test Method for Determining the Concentration of Pipeline Drag Reducer Additive in Aviation Turbine Fuels

    D7873-20 Standard Test Method for Determination of Oxidation Stability and Insolubles Formation of Inhibited Turbine Oils at 120 °C Without the Inclusion of Water (Dry TOST Method)

    D7874-13(2018) Standard Guide for Applying Failure Mode and Effect Analysis (FMEA) to In-Service Lubricant Testing

    D7875-20 Standard Test Method for Determination of Butanol and Acetone Content of Butanol for Blending with Gasoline by Gas Chromatography

    D7876-13(2018) Standard Practice for Practice for Sample Decomposition Using Microwave Heating (With or Without Prior Ashing) for Atomic Spectroscopic Elemental Determination in Petroleum Products and Lubricants

    D7889-21 Standard Test Method for Field Determination of In-Service Fluid Properties Using IR Spectroscopy

    D7898-14(2020) Standard Practice for Lubrication and Hydraulic Filter Debris Analysis (FDA) for Condition Monitoring of Machinery

    D7899-19 Standard Test Method for Measuring the Merit of Dispersancy of In-Service Engine Oils with Blotter Spot Method

    D7900-18e1 Standard Test Method for Determination of Light Hydrocarbons in Stabilized Crude Oils by Gas Chromatography

    D7901-20 Standard Specification for Dimethyl Ether for Fuel Purposes

    D7915-18 Standard Practice for Application of Generalized Extreme Studentized Deviate (GESD) Technique to Simultaneously Identify Multiple Outliers in a Data Set

    D7917-14(2018) Standard Practice for Inductive Wear Debris Sensors in Gearbox and Drivetrain Applications

    D7918-17a Standard Test Method for Measurement of Flow Properties and Evaluation of Wear, Contaminants, and Oxidative Properties of Lubricating Grease by Die Extrusion Method and Preparation

    D7919-14(2017) Standard Guide for Filter Debris Analysis (FDA) Using Manual or Automated Processes

    D7920-21 Standard Test Method for Determination of Fuel Methanol (M99) and Methanol Fuel Blends (M10 to M99) by Gas Chromatography

    D7922-14 Standard Test Method for Determination of Glycol for In-Service Engine Oils by Gas Chromatography

    D7923-19 Standard Test Method for Water in Ethanol and Hydrocarbon Blends by Karl Fischer Titration

    D7945-21 Standard Test Method for Determination of Dynamic Viscosity and Derived Kinematic Viscosity of Liquids by Constant Pressure Viscometer

    D7946-19 Standard Test Method for Initial pH (i-pH)-Value of Petroleum Products

    D7959-19 Standard Test Method for Chloride Content Determination of Aviation Turbine Fuels using Chloride Test Strip

    D7960-21 Standard Specification for Unleaded Aviation Gasoline Test Fuel Containing Non-hydrocarbon Components

    D7961-17 Standard Practice for Calibrating U-tube Density Cells over Large Ranges of Temperature and Pressure

    D7962-21 Standard Practice for Determination of Minimum Immersion Depth and Assessment of Temperature Sensor Measurement Drift

    D7963-19e1 Standard Test Method for Determination of Contamination Level of Fatty Acid Methyl Esters in Middle Distillate and Residual Fuels Using Flow Analysis by Fourier Transform Infrared Spectroscopy—Rapid Screening Method

    D7973-19 Standard Guide for Monitoring Failure Mode Progression in Plain Bearings

    D7974-21 Standard Test Method for Determination of Farnesane, Saturated Hydrocarbons, and Hexahydrofarnesol Content of Synthesized Iso-Paraffins (SIP) Fuel for Blending with Jet Fuel by Gas Chromatography

    D7975-14 Standard Test Method for Determination of Vapor Pressure of Crude Oil: VPCRx-F(Tm°C)(Manual Expansion Field Method)

    D7978-14(2019) Standard Test Method for Determination of the Viable Aerobic Microbial Content of Fuels and Associated Water—Thixotropic Gel Culture Method

    D7994-17 Standard Test Method for Total Fluorine, Chlorine, and Sulfur in Liquid Petroleum Gas (LPG) by Oxidative Pyrohydrolytic Combustion Followed by Ion Chromatography Detection (Combustion Ion Chromatography-CIC)

    D7995-19 Standard Test Method for Total Water in Liquid Butane by Liquefied Gas Sampler and Coulometric Karl Fischer Titration

    D7996-15 Standard Test Method for Measuring Visible Spectrum of Asphaltenes in Heavy Fuel Oils and Crude Oils by Spectroscopy in a Microfluidic Platform

    D8003-15a(2021) Standard Test Method for Determination of Light Hydrocarbons and Cut Point Intervals in Live Crude Oils and Condensates by Gas Chromatography

    D8004-15 Standard Test Method for Fuel Dilution of In-Service Lubricants Using Surface Acoustic Wave Sensing

    D8009-15 Standard Practice for Manual Piston Cylinder Sampling for Volatile Crude Oils, Condensates, and Liquid Petroleum Products

    D8011-19 Standard Specification for Natural Gasoline as a Blendstock in Ethanol Fuel Blends or as a Denaturant for Fuel Ethanol

    D8022-20 Standard Test Method for Roll Stability of Lubricating Grease in Presence of Water (Wet Roll Stability Test)

    D8029-18 Standard Specification for Biodegradable, Low Aquatic Toxicity Hydraulic Fluids

    D8045-17e1 Standard Test Method for Acid Number of Crude Oils and Petroleum Products by Catalytic Thermometric Titration

    D8046-16a Standard Guide for Pumpability of Heat Transfer Fluids

    D8047-19 Standard Test Method for Evaluation of Engine Oil Aeration Resistance in a Caterpillar C13 Direct-Injected Turbocharged Automotive Diesel Engine

    D8048-21 Standard Test Method for Evaluation of Diesel Engine Oils in T-13 Diesel Engine

    D8049-21 Standard Test Method for Determining Concentration, Count, and Size Distribution of Solid Particles and Water in Light and Middle Distillate Fuels by Direct Imaging Analyzer

    D8056-18 Standard Guide for Elemental Analysis of Crude Oil

    D8070-21 Standard Test Method for Screening of Fuels and Fuel Associated Aqueous Specimens for Microbial Contamination by Lateral Flow Immunoassay

    D8071-21 Standard Test Method for Determination of Hydrocarbon Group Types and Select Hydrocarbon and Oxygenate Compounds in Automotive Spark-Ignition Engine Fuel Using Gas Chromatography with Vacuum Ultraviolet Absorption Spectroscopy Detection (GC-VUV)

    D8072-17 Standard Classification for Reporting Solids and Insoluble Water Contamination of Hydrocarbon-Based Petroleum Products When Analyzed by Imaging Instrumentation

    D8073-16(2021) Standard Test Method for Determination of Water Separation Characteristics of Aviation Turbine Fuel by Small Scale Water Separation Instrument

    D8074-19 Standard Test Method for Evaluation of Diesel Engine Oils in DD13 Diesel Engine

    D8076-21a Standard Specification for 100 Research Octane Number Test Fuel for Automotive Spark-Ignition Engines

    D8092-17 Standard Test Method for Field Determination of Kinematic Viscosity Using a Microchannel Viscometer

    D8094-21 Standard Test Method for Determination of Water Content of Liquefied Petroleum Gases (LPG) Using an Online Electronic Moisture Analyzer

    D8097-17e1 Standard Test Method for Determination of Bulk Density for Specific Size Fractions of Calcined Petroleum Coke Using a Transaxial Pressure Pycnometer

    D8098-17 Standard Test Method for Permanent Gases in C2 and C3 Hydrocarbon Products by Gas Chromatography and Pulse Discharge Helium Ionization Detector

    D8110-17 Standard Test Method for Elemental Analysis of Distillate Products by Inductively Coupled Plasma Mass Spectrometry (ICP-MS)

    D8111-21a Standard Test Method for Evaluation of Automotive Engine Oils in the Sequence IIIH, Spark-Ignition Engine

    D8112-17 Standard Guide for Obtaining In-Service Samples of Turbine Operation Related Lubricating Fluid

    D8114-21a Standard Test Method for Measurement of Effects of Automotive Engine Oils on Fuel Economy of Passenger Cars and Light-Duty Trucks in Sequence VIE Spark Ignition

    D8120-17 Standard Test Method for Ferrous Debris Quantification

    D8126-17 Standard Test Method for Efficient Basicity Determination by Potentiometric Hydrochloric Acid Titration

    D8127-17e1 Standard Test Method for Coupled Particulate and Elemental Analysis using X-ray Fluorescence (XRF) for In-Service Lubricants

    D8128-17 Standard Guide for Monitoring Failure Mode Progression in Industrial Applications with Rolling Element Ball Type Bearings

    More Information


    Print or NOW get Online Access to this Volume
    (Basic or Plus)

    View Contents

    - 2021
       Standards: 170
       Pages: 2044

    - 2020
       Standards: 154
       Pages: 1956