New Standards

D3311-11(2016) Standard Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns

F2331-11(2016) Standard Test Method for Determining Chemical Compatibility of Substances in Contact with Thermoplastic Pipe and Fittings Materials

C506-16 Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe

C506M-16 Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric)

D4802-15 Standard Specification for Poly(Methyl Methacrylate) Acrylic Plastic Sheet

C581-15 Standard Practice for Determining Chemical Resistance of Thermosetting Resins Used in Glass-Fiber-Reinforced Structures Intended for Liquid Service

D1598-15a Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

D4167-15 Standard Specification for Fiber-Reinforced Plastic Fans and Blowers

D7856-15a Standard Specification for Color and Appearance Retention of Solid and Variegated Color Plastic Siding Products using CIELab Color Space

D7990-15 Standard Test Method for Using Reflectance Spectra to Produce an Index of Temperature Rise in Polymeric Siding

F2023-15 Standard Test Method for Evaluating the Oxidative Resistance of Crosslinked Polyethylene (PEX) Pipe, Tubing and Systems to Hot Chlorinated Water

F2136-08(2015) Standard Test Method for Notched, Constant Ligament-Stress (NCLS) Test to Determine Slow-Crack-Growth Resistance of HDPE Resins or HDPE Corrugated Pipe

F1803-15 Standard Specification for Poly (Vinyl Chloride)(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter 

D1598-15 Standard Test Method for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

D3034-15 Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings

F1336-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings

F2634-15 Standard Test Method for Laboratory Testing of Polyethylene (PE) Butt Fusion Joints using Tensile-Impact Method

F2829/F2829M-15 Standard Specification for Metric- and Inch-Sized Crosslinked Polyethylene (PEX) Pipe Systems

G100-89(2015) Standard Test Method for Conducting Cyclic Galvanostaircase Polarization

G102-89(2015)e1 Standard Practice for Calculation of Corrosion Rates and Related Information from Electrochemical Measurements

G106-89(2015) Standard Practice for Verification of Algorithm and Equipment for Electrochemical Impedance Measurements

G108-94(2015) Standard Test Method for Electrochemical Reactivation (EPR) for Detecting Sensitization of AISI Type 304 and 304L Stainless Steels

C507-15 Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe

C507M-15 Standard Specification for Reinforced Concrete Elliptical Culvert, Storm Drain, and Sewer Pipe (Metric)

C1818-15 Standard Specification for Synthetic Fiber Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

C76-15a Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

C76M-15 Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)

C655-15 Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe

C655M-15 Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)

D1243-15 Standard Test Method for Dilute Solution Viscosity of Vinyl Chloride Polymers

D1755-15 Standard Specification for Poly(Vinyl Chloride) Resins

D4396-15 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications

D5336-15a Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials

D5926-15 Standard Specification for Poly (Vinyl Chloride) (PVC) Gaskets for Drain, Waste, and Vent (DWV), Sewer, Sanitary, and Storm Plumbing Systems

D6263-15 Standard Specification for Extruded Rods and Bars Made From Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC)

D7082-15 Standard Specification for Polyethylene Stay In Place Form System for End Walls for Drainage Pipe

E2843-15 Standard Specification for Demonstrating That a Building is in Walkable Proximity to Neighborhood Assets

A74-15 Standard Specification for Cast Iron Soil Pipe and Fittings

A888-15 Standard Specification for Hubless Cast Iron Soil Pipe and Fittings for Sanitary and Storm Drain, Waste, and Vent Piping Applications

D1710-15 Standard Specification for Extruded Polytetrafluoroethylene (PTFE) Rod, Heavy Walled Tubing and Basic Shapes

D3159-15 Standard Specification for Modified ETFE Fluoropolymer Molding and Extrusion Materials

D3294-15 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet and Molded Basic Shapes

D3295-15 Standard Specification for PTFE Tubing, Miniature Beading and Spiral Cut Tubing

D4549-15 Standard Classification System and Basis for Specification for Polystyrene and Rubber-Modified Polystyrene Molding and Extrusion Materials (PS)

D6150-15 Standard Test Method for Estimating Processing Losses of Plastisols and Organosols Due to Volatility

E2844-15 Standard Specification for Demonstrating That a Building’s Location Provides Access to Public Transit

E2844-15e1 Standard Specification for Demonstrating That a Building’s Location Provides Access to Public Transit

F1417-11a(2015) Standard Practice for Installation Acceptance of Plastic Non-pressure Sewer Lines Using Low-Pressure Air

F1588-96(2015) Standard Test Method for Constant Tensile Load Joint Test (CTLJT)

F2389-15 Standard Specification for Pressure-rated Polypropylene (PP) Piping Systems

F2618-15 Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems

F2806-10(2015) Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe (Metric SDR-PR)

F2881-11(2015) Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications

C1540-15 Standard Specification for Heavy Duty Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings

D5436-15 Standard Specification for Cast Poly(Methyl Methacrylate) Plastic Rods, Tubes, and Shapes

F3149-15 Standard Practice for Determining the Maintenance Factor (m) and Yield Factor (y) Loading Constants Applicable to Gasket Materials and Designs

D3935-15 Standard Classification System and Basis for Specification for Polycarbonate (PC) Unfilled and Reinforced Material

F645-15a Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

F3097-15 Standard Practice for Installation of an Outside Sewer Service Cleanout through a Minimally Invasive Small Bore Vacuum Excavation

C1277-15 Standard Specification for Shielded Couplings Joining Hubless Cast Iron Soil Pipe and Fittings

D706-15 Standard Classification System and Basis for Specifications for Cellulose Acetate Molding and Extrusion Compounds (CA)

D707-15 Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB)

D1562-15 Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP)

D1693-15 Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics

D2143-15 Standard Test Method for Cyclic Pressure Strength of Reinforced, Thermosetting Plastic Pipe

D2996-15 Standard Specification for Filament-Wound “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

D2997-15 Standard Specification for Centrifugally Cast “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

D3222-05(2015) Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials

D4024-15 Standard Specification for Machine Made “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges

D4068-15 Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane

D4441-15 Standard Specification for Aqueous Dispersions of Polytetrafluoroethylene

D4726-15 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Exterior-Profile Extrusions Used for Assembled Windows and Doors

D4894-15 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding and Ram Extrusion Materials

D4895-15 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Produced From Dispersion

D5421-15 Standard Specification for Contact Molded “Fiberglass” (Glass-Fiber-Reinforced Thermosetting Resin) Flanges

F667/F667M-15 Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings

D789-15 Standard Test Methods for Determination of Solution Viscosities of Polyamide (PA)

D5336-15 Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Materials

D5857-15 Standard Specification for Polypropylene Injection and Extrusion Materials Using ISO Protocol and Methodology

D7254-15 Standard Specification for Polypropylene (PP) Siding

D7856-15 Standard Specification for Color and Appearance Retention of Solid and Variegated Color Plastic Siding Products using CIELab Color Space

F645-15 Standard Guide for Selection, Design, and Installation of Thermoplastic Water- Pressure Piping Systems

F949-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings

F3128-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core

D2122-15 Standard Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

F610/F610M-15 Standard Practice for Evaluating the Quality of Molded Poly(Vinyl Chloride) (PVC) Plastic Pipe Fittings by the Heat Reversion Technique

F679-15 Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings

F1697-09(2015) Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Strip for Machine Spiral-Wound Liner Pipe Rehabilitation of Existing Sewers and Conduit

F1698-02(2015) Standard Practice for Installation of Poly(Vinyl Chloride)(PVC) Profile Strip Liner and Cementitious Grout for Rehabilitation of Existing Man-Entry Sewers and Conduits

F1735-09(2015) Standard Specification for Poly (Vinyl Chloride) (PVC) Profile Strip for PVC Liners for Rehabilitation of Existing Man-Entry Sewers and Conduits

F2718-09(2015) Standard Specification for Polyethylene (PE) and Cement Materials for an Encapsulated Cement Mortar Formed in Place Liner System (FIPLS) for the Rehabilitation of Water Pipelines

F2719-09(2015) Standard Practice for Installation of Polyethylene (PE) and Encapsulated Cement Mortar Formed in Place Lining System (FIPLS) for the Rehabilitation of Water Pipelines