ASTM F880M - 02(2008)

    Standard Specification for Stainless Steel Socket Set Screws (Metric)

    Active Standard ASTM F880M | Developed by Subcommittee: F16.04

    Book of Standards Volume: 01.08


    Buy Standard (PDF)
    5 pages
    $42.00
    Buy Standard (Print)
    5 pages
    $42.00
    Buy Standard + Redline (PDF)
    10 pages
    $50.40

    Historical (view previous versions of standard)


    ASTM F880M

    Abstract

    This specification covers the requirements for austenitic grade stainless steel socket set screws (SSS), sizes M1.6 through M24, having property classes A1-50 and A1-70. The analysis of the screw material shall conform to the chemical composition specified. Socket set screw shall be subjected to torque test, Vickers hardness test, and corrosion resistance test to meet the requirements prescribed.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers the requirements for austenitic grade stainless steel socket set screws (SSS), sizes M1.6 through M24, having Property Classes A1-50 and A1-70.

    1.2 UnitsThe values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    Note 1—This specification is the metric companion of Specification F 880.

    1.3 The following hazard caveat pertains only to Section 11, the Test Method Section: This standard does not purport to address the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels

    A342/A342M Test Methods for Permeability of Feebly Magnetic Materials

    A380 Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems

    A555/A555M Specification for General Requirements for Stainless Steel Wire and Wire Rods

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A967 Specification for Chemical Passivation Treatments for Stainless Steel Parts

    D3951 Practice for Commercial Packaging

    E3 Guide for Preparation of Metallographic Specimens

    E18 Test Methods for Rockwell Hardness of Metallic Materials

    E92 Test Method for Vickers Hardness of Metallic Materials

    E384 Test Method for Knoop and Vickers Hardness of Materials

    F738M Specification for Stainless Steel Metric Bolts, Screws, and Studs

    F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F880 Specification for Stainless Steel Socket-Set Screws

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    ASME Standard

    B18.3.6M Metric Series Socket Set Screws R Available from Global Engineering Documents, 15 Inverness Way, East Englewood, CO 80112-5704, http://www.global.ihs.com.


    ICS Code

    ICS Number Code 21.060.10 (Bolts, screws, studs)

    UNSPSC Code

    UNSPSC Code 31161518(Socket screw )


    DOI: 10.1520/F0880M-02R08

    ASTM International is a member of CrossRef.

    ASTM F880M

    Citing ASTM Standards
    Back to Top