ASTM F837M - 02a(2010)

    Standard Specification for Stainless Steel Socket Head Cap Screws [Metric]

    Active Standard ASTM F837M | Developed by Subcommittee: F16.04

    Book of Standards Volume: 01.08


    Buy Standard (PDF)
    8 pages
    $42.00
    Buy Standard (Print)
    8 pages
    $42.00

    Historical (view previous versions of standard)


    ASTM F837M

    Abstract

    This specification covers stainless steel metric socket head cap screws (SHCS) intended for use in applications requiring general corrosion resistance. Two groups of stainless steel alloys are covered, austenitic Grade A1 and martensitic Grade C1. Four property classes are covered: austenitic A1-50 in an annealed condition; austenitic A1-55 in a cold worked condition; austenitic A1-70 in a cold worked condition, and martensitic C1-110 in a heat treated condition. Materials shall be tested and the individual grades shall conform to forging; threads; heat treatment; chemical composition; mechanical properties such as thread diameter, tensile strength, yield strength, elongation, core hardness (Vickers and Rockwell); and corrosion resistance values. Workmanship, finish, and appearance are also detailed.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers the chemical and mechanical requirements for stainless steel metric socket head cap screws (SHCS) with nominal thread M1.6 through M36 and intended for use in applications requiring general corrosion resistance.

    1.2 Two groups of stainless steel alloys are covered, austenitic Grade A1 and martensitic Grade C1.

    1.3 Four property classes are covered: austenitic A1-50 in an annealed condition at 585 MPa maximum; austenitic A155 in a cold worked condition at 550 MPa minimum; austenitic A1-70 in a cold worked condition at 700 MPa minimum, and martensitic C1-110 in a heat treated condition at 1100 MPa minimum.

    1.4 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.5 This hazard statement pertains only to Section 13, Test Methods: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A262 Practices for Detecting Susceptibility to Intergranular Attack in Austenitic Stainless Steels

    A342/A342M Test Methods for Permeability of Feebly Magnetic Materials

    A380 Practice for Cleaning, Descaling, and Passivation of Stainless Steel Parts, Equipment, and Systems

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    A967 Specification for Chemical Passivation Treatments for Stainless Steel Parts

    D3951 Practice for Commercial Packaging

    E18 Test Methods for Rockwell Hardness of Metallic Materials

    E92 Test Method for Vickers Hardness of Metallic Materials

    E384 Test Method for Knoop and Vickers Hardness of Materials

    F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric)

    F738M Specification for Stainless Steel Metric Bolts, Screws, and Studs

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    ASME Standard

    ASMEB18.3.1M Socket Head Cap Screws (Metric Series) Available from Global Engineering Documents, 15 Inverness Way, East Englewood, CO 80112-5704, http://www.global.ihs.com.


    ICS Code

    ICS Number Code 21.060.10 (Bolts, screws, studs)

    UNSPSC Code

    UNSPSC Code 31161501(Cap screws )


    DOI: 10.1520/F0837M-02AR10

    ASTM International is a member of CrossRef.

    ASTM F837M

    Citing ASTM Standards
    Back to Top