ASTM F835M - 11

    Standard Specification for Alloy Steel Socket Button and Flat Countersunk Head Cap Screws (Metric)

    Active Standard ASTM F835M | Developed by Subcommittee: F16.02

    Book of Standards Volume: 01.08


    Buy Standard (PDF)
    5 pages
    $42.00
    Buy Standard (Print)
    5 pages
    $42.00
    Buy Standard + Redline (PDF)
    10 pages
    $50.40

    Historical (view previous versions of standard)


    ASTM F835M

    Abstract

    This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws. The screws shall be fabricated from alloy steel made to fine grain practice. The chemical composition of the screw material shall conform to the heat analysis specified. Hardness, tensile strength, yield strength, elongation, and area reduction shall be tested to meet the requirements prescribed.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers the requirements for quenched and tempered alloy steel hexagon socket button (SBHCS) and flat countersunk (SFHCS) head cap screws M3 through M20 thread sizes having material properties of ISO 898/1 Property Class 12.9.

    1.2 Fasteners meeting this specification are intended for shear type applications and have tensile requirements equivalent to ISO 898/1 Property Class 10.9.

    1.3 The hazard statement pertains only to the test method section, Section 11 of this specification. This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ANSI/ASME Standards

    B18.24 Part Identifying Number (PIN) Code System Standard for B18 Fastener Products Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990, http://www.asme.org.

    ISO Standard

    898/1 Mechanical properties of fasteners made of carbon steel and alloy steel -- Part 1: Bolts, screws and studs with specified property classes -- Coarse thread and fine pitch thread

    ASTM Standards

    A751 Test Methods, Practices, and Terminology for Chemical Analysis of Steel Products

    E3 Guide for Preparation of Metallographic Specimens

    E112 Test Methods for Determining Average Grain Size

    E384 Test Method for Knoop and Vickers Hardness of Materials

    F606M Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, and Rivets (Metric)

    F788/F788M Specification for Surface Discontinuities of Bolts, Screws, and Studs, Inch and Metric Series

    F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection

    F2328 Test Method for Determining Decarburization and Carburization in Hardened and Tempered Threaded Steel Bolts, Screws and Studs


    ICS Code

    ICS Number Code 21.060.10 (Bolts, screws, studs)

    UNSPSC Code

    UNSPSC Code 31161501(Cap screws)


    DOI: 10.1520/F0835M-11

    ASTM International is a member of CrossRef.

    ASTM F835M

    Citing ASTM Standards
    Back to Top