ASTM F718 - 07(2011)e1

    Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet

    Active Standard ASTM F718 | Developed by Subcommittee: F25.01

    Book of Standards Volume: 01.07


      Format Pages Price  
    PDF 4 $38.00   ADD TO CART
    Hardcopy (shipping and handling) 4 $38.00   ADD TO CART
    Standard + Redline PDF Bundle 8 $45.60   ADD TO CART


    Abstract

    The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet2 provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. When filling out the Product/Procedure Data Sheet remember that the information contained therein will be utilized by both technical and production personnel. The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 The Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet provides on one sheet needed information concerning the characteristics of a specific paint or coating to include generic description, physical properties, surface preparation requirements, application requirements, and safety. The front side of the sheet contains four major, numbered paragraphs and a highlighted section for Special Safety Precautions. These paragraphs are as follows:

    I. Generic Type and Description

    II. Manufacturers Data

    III. Properties

    IV. Surface Preparation Minimum Requirements

    The back side of the page contains the following paragraphs:

    V. Mixing Procedure

    VI. Application

    1.2 The completed data sheets can be used by technical personnel to help evaluate the technical acceptability of a proposed material, by production personnel to evaluate production compatibility of proposed materials and to provide application instructions for selected paints and coatings materials, and by quality control personnel to verify attributes of materials.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D56 Test Method for Flash Point by Tag Closed Cup Tester

    D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester

    D523 Test Method for Specular Gloss

    D1475 Test Method For Density of Liquid Coatings, Inks, and Related Products

    D1640 Test Methods for Drying, Curing, or Film Formation of Organic Coatings at Room Temperature

    D1650 Test Methods for Sampling and Testing Shellac Varnish

    D2697 Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings

    D3278 Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus

    U.S. EPA Method

    24 U.S. Environmental Protection Agency, 40 CFR Ch. 1, Part 60, Appendix A, Determination of Volatile Matter Content, Density, Volume Solids, and Weight Solids of Surface Coatings


    ICS Code

    ICS Number Code 47.020.05 (Materials and components for shipbuilding)

    UNSPSC Code

    UNSPSC Code


    Referencing This Standard

    DOI: 10.1520/F0718-07R11E01

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM F718-07(2011)e1, Standard Specification for Shipbuilders and Marine Paints and Coatings Product/Procedure Data Sheet, ASTM International, West Conshohocken, PA, 2007, www.astm.org

    Back to Top