Abstract
This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs manufactured from a number of alloys in common use and are intended for general service applications. The specimens shall be made of materials that conform to the chemical composition requirements for copper, nickel, aluminum, and titanium alloys that are to be determined by chemical analysis. Manufacturing of the specimens shall be by cold or hot forming or machining and stress relieving. Tension, hardness, and shear tests shall be performed to determine the mechanical properties of the specimen which shall be in compliance with the tensile strength, yield strength, elongation, hardness, and shear strength requirements.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
Significance and Use
For purposes of determining compliance with the specified limits for requirements of the properties listed in this specification, an observed value or calculated value shall be rounded in accordance with Practice E29.
1. Scope
1.1 This specification covers the requirements for commercial wrought nonferrous bolts, hex cap screws, and studs 0.250 to 1.500 in. inclusive in diameter manufactured from a number of alloys in common use and intended for general service applications.
1.2 Applicable nuts for use with bolts, cap screws, and studs covered by this specification are covered by Specification F467.
Note 1—A complete metric companion to Specification F468 has been developedF468M; therefore no metric equivalents are presented in this specification.
2. Referenced Documents (purchase separately) 
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
B154 Test Method for Mercurous Nitrate Test for Copper Alloys
B193 Test Method for Resistivity of Electrical Conductor Materials
B211 Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire
B565 Test Method for Shear Testing of Aluminum and Aluminum-Alloy Rivets and Cold-Heading Wire and Rods
B574 Specification for Low-Carbon Nickel-Chromium-Molybdenum, Low-Carbon Nickel-Molybdenum-Chromium-Tantalum, Low-Carbon Nickel-Chromium-Molybdenum-Copper, and Low-Carbon Nickel-Chromium-Molybdenum-Tungsten Alloy Rod
D3951 Practice for Commercial Packaging
E8 Test Methods for Tension Testing of Metallic Materials
E18 Test Methods for Rockwell Hardness of Metallic Materials
E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
E34 Test Methods for Chemical Analysis of Aluminum and Aluminum-Base Alloys
E38 Methods for Chemical Analysis of Nickel-Chromium and Nickel-Chromium-Iron Alloys
E53 Test Method for Determination of Copper in Unalloyed Copper by Gravimetry
E54 Test Methods for Chemical Analysis of Special Brasses and Bronzes
E55 Practice for Sampling Wrought Nonferrous Metals and Alloys for Determination of Chemical Composition
E62 Test Methods for Chemical Analysis of Copper and Copper Alloys (Photometric Methods)
E75 Test Methods for Chemical Analysis of Copper-Nickel and Copper-Nickel-Zinc Alloys
E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys
E92 Test Method for Vickers Hardness of Metallic Materials
E101 Test Method for Spectrographic Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique
E120 Test Methods for Chemical Analysis of Titanium and Titanium Alloys
E165 Practice for Liquid Penetrant Examination for General Industry
E227 Test Method for Optical Emission Spectrometric Analysis of Aluminum and Aluminum Alloys by the Point-to-Plane Technique
E354 Test Methods for Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys
E478 Test Methods for Chemical Analysis of Copper Alloys
E1409 Test Method for Determination of Oxygen and Nitrogen in Titanium and Titanium Alloys by the Inert Gas Fusion Technique
F467 Specification for Nonferrous Nuts for General Use
F606 Test Methods for Determining the Mechanical Properties of Externally and Internally Threaded Fasteners, Washers, Direct Tension Indicators, and Rivets
F1470 Practice for Fastener Sampling for Specified Mechanical Properties and Performance Inspection
ASME Standards
ASMEH35.1 Alloy and Temper Designation Systems for Aluminum
Index Terms
bolts; cap screws; general use; nonferrous; studs; Aluminum alloys--specifications; Copper; Copper alloy--specifications; Fasteners (metal)--specifications; Naval brass; Nickel; Nickel alloy bolting materials--specifications; Nickel-copper alloy--specifications; Nickel-copper-aluminum alloys; Nickel-molybdenum alloys--specifications; Nickel-molybdenum-chromium alloys--specifications; Nonferrous bolting materials; Palladium (titanium plus palladium)--specifications; Titanium plus palladium--specifications; Titanium (Ti)/alloys--specifications; UNS N04400 (Ni-Cu alloy, Monel 400); UNS N04405 (Ni-Cu alloy solution strengthened (Monel R405)); UNS N05500 (Ni-Cu alloy, Monel K500); UNS N10001 (Ni-Mo alloy, Hastelloy B); UNS N10002 (Ni-Mo alloy, Hastelloy C); UNS N10665 (Ni-Mo alloy, Hastelloy B-2); UNS R50250 (Ti, unalloyed); UNS R50400 (Ti, unalloyed); UNS R50550 (Ti, unalloyed); UNS R50700 (Ti, unalloyed); Yellow brass;
ICS Code
ICS Number Code 21.060.10 (Bolts, screws, studs)
DOI: 10.1520/F0468-10
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
