ASTM F2363 / F2363M - 12

    Standard Specification for Sewage and Graywater Flow Through Treatment Systems

    Active Standard ASTM F2363 / F2363M | Developed by Subcommittee: F25.06

    Book of Standards Volume: 01.07


      Format Pages Price  
    PDF Version 16 $48.00   ADD TO CART
    Print Version 16 $48.00   ADD TO CART
    Standard + Redline PDF Bundle 32 $57.60   ADD TO CART


    Abstract

    This specification covers the material, design, manufacture, performance, operation, functioning, and testing requirements for United States Coast Guard (USCG) Type II Marine Sanitation Devices or IMO MARPOL 73/78 Annex IV flow through treatment device intended to process sewage and graywater generated during the ship's normal service. It is intended for use by purchasers, designers, and manufacturers of shipboard environmental pollution control equipment to determine the requirements for equipment purchase, equipment use, and design considerations. The marine sanitation devices shall perform accordingly to the following tests: vibration test; shock test; rolling test; pressure test; pressure and vacuum pulse test; temperature range test; chemical resistance test; operability test; sewage processing test; coliform test; suspended solids test; and ignition prevention test. Aside from meeting the requirements set forth herein, the devices shall also be designed and installed to conform to human engineering principles to th degree that it can be operated and maintained by males and females of specified heights.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers the design, manufacture, performance, operation, and testing of flow through treatment systems intended to process sewage or graywater, or both, generated during a ship's normal service. This specification is intended for use by designers, manufacturers, purchasers, and operators of shipboard environmental pollution control equipment to determine the requirements for equipment design, manufacture, purchase, and in-service operation.

    1.2 The treatment system shall be capable of meeting the effluent requirements detailed in Section 4 with respect to a ship's operational area.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    9.1 This test method uses performance-based quantitative procedures for evaluation, inspection, and testing of sewage or graywater flow through treatment systems.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A307 Specification for Carbon Steel Bolts and Studs, 60 000 PSI Tensile Strength

    A563 Specification for Carbon and Alloy Steel Nuts

    B117 Practice for Operating Salt Spray (Fog) Apparatus

    B165 Specification for Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube

    D1253 Test Method for Residual Chlorine in Water

    E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves

    F906 Specification for Letters and Numerals for Ships

    F992 Specification for Valve Label Plates

    F993 Specification for Valve Locking Devices

    F998 Specification for Centrifugal Pump, Shipboard Use

    F1030 Practice for Selection of Valve Operators

    F1098 Specification for Envelope Dimensions for Butterfly Valves--NPS 2 to 24

    F1122 Specification for Quick Disconnect Couplings (6 in. NPS and Smaller)

    F1155 Practice for Selection and Application of Piping System Materials

    F1166 Practice for Human Engineering Design for Marine Systems, Equipment, and Facilities

    F1298 Specification for Flexible, Expansion-Type Ball Joints for Marine Applications

    F1323 Specification for Shipboard Incinerators

    F1387 Specification for Performance of Piping and Tubing Mechanically Attached Fittings

    F1510 Specification for Rotary Positive Displacement Pumps, Ships Use

    F1511 Specification for Mechanical Seals for Shipboard Pump Applications

    F2044 Specification for Liquid Level Indicating Equipment, Electrical


    ICS Code

    ICS Number Code 13.030.20 (Liquid wastes. Sludge)

    UNSPSC Code

    UNSPSC Code 25111900(Marine craft systems and subassemblies)


    DOI: 10.1520/F2363_F2363M-12

    ASTM International is a member of CrossRef.

    ASTM F2363 / F2363M

    Citing ASTM Standards
    Back to Top