ASTM F2307-03

    Standard Specification for Series 10 Poly(Vinyl Chloride) (PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter (Withdrawn 2011)

    Withdrawn Standard: ASTM F2307-03 | Developed by Subcommittee: F17.62

    WITHDRAWN, NO REPLACEMENT


      Format Pages Price  
    PDF 5 $51.60   ADD TO CART


    Withdrawn Rationale:

    Rationale

    This specification covers requirements for 10 psi pipe stiffness poly(vinyl chloride) (PVC) closed profile sewer pipe and fittings with integral bell and elastomeric seal joints or plain end pipe with couplings in sizes (18 to 60 in.) based on a controlled inside diameter.

    Formerly under the jurisdiction of Committee F17 on Plastic Piping Systems, this specification was withdrawn in August 2011 because the committee is not aware of any producers or distributors of the product described by the standard.

    1. Scope

    1.1 This specification covers requirements for 10 psi pipe stiffness poly(vinyl chloride) (PVC) closed profile sewer pipe and fittings with integral bell and elastomeric seal joints or plain end pipe with couplings in sizes (18 to 60 in.) based on a controlled inside diameter.

    1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

    1.3 The following safety hazard caveat pertains only to the test methods portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Note 1—Pipe and fittings produced to this specification should be installed in accordance with Practice D 2321.



    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D618 Practice for Conditioning Plastics for Testing

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion

    D2321 Practice for Underground Installation of Flexible Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

    D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2444 Test Method for Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

    D2855 Practice for Making Solvent-Cemented Joints with Poly(Vinyl Chloride) (PVC) Pipe and Fittings

    D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

    F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

    F412 Terminology Relating to Plastic Piping Systems

    F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

    F679 Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings

    Federal Standard

    Fed.Std.No.123 Marking for Shipment (Civil Agencies)

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage


    DOI: 10.1520/F2307-03

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM F2307-03, Standard Specification for Series 10 Poly(Vinyl Chloride) (PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter (Withdrawn 2011), ASTM International, West Conshohocken, PA, 2003, www.astm.org

    Back to Top