ASTM F2012 - 13

    Standard Consumer Safety Performance Specification for Stationary Activity Centers

    Active Standard ASTM F2012 | Developed by Subcommittee: F15.17

    Book of Standards Volume: 15.11

      Format Pages Price  
    PDF 11 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 11 $48.00   ADD TO CART
    Standard + Redline PDF Bundle 22 $57.60   ADD TO CART

    1. Scope

    1.1 This consumer safety performance specification covers performance requirements, test methods and marking requirements to promote safe use of a stationary activity center by an occupant.

    1.2 This consumer safety performance specification is intended to minimize the risk of incidents to an occupant resulting from normal use and reasonably foreseeable misuse or abuse of a stationary activity center.

    1.3 No stationary activity center produced after the approval date of this consumer safety performance specification shall, either by label or other means, indicate compliance with this specification unless it conforms to all requirements contained herein.

    1.4 This consumer safety performance specification is not intended to address incidents and injuries resulting from the interaction of other persons with the child occupant in the stationary activity center or the incidents resulting from abuse and misuse by children able to walk.

    1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.6 The following precautionary caveat pertains only to the test methods portion, Section 7, of this consumer safety performance specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D3359 Test Methods for Measuring Adhesion by Tape Test

    F963 Consumer Safety Specification for Toy Safety

    Federal Regulations:‚ÄČ

    16CFR1303 Ban of Lead-Containing Paint and Certain Consumer Products Bearing Lead-Containing Paint

    16CFR1500 Hazardous Substances Act Regulations including sections:1500.18(a)(6) Banned Toys and Other Banned Articles Intended for Use by Children1500.48 Technical Requirements for Determining a Sharp Point in Toys or Other Articles Intended for Use by Children Under Eight Years of Age1500.49 Technical Requirements for Determining a Sharp Metal or Glass Edge in Toys or Other Articles Intended for Use by Children Under Eight Years of Age1500.50-.52 Test Methods for Simulating Use and Abuse of Toys and Other Articles Intended for Use by Children15.00.86(a)(4) Exemptions from Classification as a Banned Article for Use by Children

    16CFR1501 Method for Identifying Toys and Other Articles Intended for Use by Children Under Three Years of Age Which Present Choking, Aspiration or Ingestion Hazards Because of Small Parts

    Other References

    CAMIInfantDummy, Mark II (see ) Department of Transportation Memorandum Report AAC-119-74-14, Revision II, Drawing No. SA-1001 by Richard Chandler, July 2, 1974. Federal Aviation Administration, Civil Aeromedical Institute, Protection and Survival Laboratory, Aeronautical Center, Oklahoma City, OK 73125.

    Other Standards

    ASME/ANSIB16.9 Factory-Made Wrought Steel Buttwelding Fittings Available from American Society of Mechanical Engineers (ASME), ASME International Headquarters, Three Park Ave., New York, NY 10016-5990,

    ICS Code

    ICS Number Code 97.190 (Equipment for children)

    UNSPSC Code

    UNSPSC Code 56101803(Carriages or perambulators or strollers)

    DOI: 10.1520/F2012

    ASTM International is a member of CrossRef.

    ASTM F2012

    Citing ASTM Standards
    Back to Top