ASTM F1871 - 11

    Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation

    Active Standard ASTM F1871 | Developed by Subcommittee: F17.67

    Book of Standards Volume: 08.04


      Format Pages Price  
    PDF 5 $42.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $42.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $50.40   ADD TO CART


    1. Scope

    1.1 This specification covers requirements and test methods for materials, dimensions, workmanship, flattening resistance, impact resistance, pipe stiffness, extrusion quality, and a form of marking for folded/formed poly (vinyl chloride) (PVC) pipe for existing sewer and conduit rehabilitation.

    1.2 Pipe produced to this specification is for use in non-pressure sewer and conduit rehabilitation where the folded PVC pipe is installed into and then expanded to provide a close fit to the wall of the original conduit, forming a new structural pipe-within-a-pipe.

    Note 1—For installation procedures refer to Practice F1867.

    1.3 This specification includes pipe made only from materials specified in Section 6. This specification does not include pipe manufactured from reprocessed, recycled, or reclaimed PVC.

    1.4 The values stated in inch-pound units are to be regarded as the standard. The SI units given in parentheses are provided for information only.

    1.5 The following precautionary statement pertains only to the test method portion, Section 11, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.6 There is no similar or equivalent ISO Standard.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D618 Practice for Conditioning Plastics for Testing

    D638 Test Method for Tensile Properties of Plastics

    D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position

    D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion

    D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

    F412 Terminology Relating to Plastic Piping Systems

    F1057 Practice for Estimating the Quality of Extruded Poly (Vinyl Chloride) (PVC) Pipe by the Heat Reversion Technique

    F1867 Practice for Installation of Folded/Formed Poly (Vinyl Chloride) (PVC) Pipe Type A for Existing Sewer and Conduit Rehabilitation

    Federal Standard

    Fed.Std.No.123 Marking for Shipment (Civil Agencies)

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage


    ICS Code

    ICS Number Code 23.040.20 (Plastic pipes); 83.080.20 (Thermoplastic materials)

    UNSPSC Code

    UNSPSC Code 40171517(Commercial PVC pipe)


    DOI: 10.1520/F1871-11

    ASTM International is a member of CrossRef.

    ASTM F1871

    Citing ASTM Standards
    Back to Top