ASTM F1718 - 01(2013)

    Standard Specification for Rotary Positive Displacement Distillate Fuel Pumps

    Active Standard ASTM F1718 | Developed by Subcommittee: F25.11

    Book of Standards Volume: 01.07


      Format Pages Price  
    PDF 7 $42.00   ADD TO CART
    Hardcopy (shipping and handling) 7 $42.00   ADD TO CART


    Abstract

    This specification covers the design and construction requirements of rotary positive displacement distillate fuel pumps intended for use in shipboard. Pumps covered by this specification are of Types II, III, IV, V, VIII, X, and XI and of sizes A-H. The pump shall be manufactured capable of sustaining operation in any direction up to a certain inclination, shall withstand environmental vibration induced by shipboard machinery and equipment, shall be driven by an electric motor, and besides distillate fuel, the pump shall also be used to pump aviation turbine fuel. Performance acceptance tests shall be performed, including mechanical running test, noise test, and hydrostatic test, and shall conform to the requirements specified.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    Significance and Use

    1. Scope

    1.1 This specification covers the requirements applicable to the design and construction of rotary positive displacement distillate fuel pumps for shipboard use.

    1.2 Lineal dimensions and units of force in this specification are expressed as inches and pounds respectively. A companion metric standard is in the process of preparation.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A36/A36M Specification for Carbon Structural Steel

    A53/A53M Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated, Welded and Seamless

    A106/A106M Specification for Seamless Carbon Steel Pipe for High-Temperature Service

    A193/A193M Specification for Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service and Other Special Purpose Applications

    A194/A194M Specification for Carbon and Alloy Steel Nuts for Bolts for High Pressure or High Temperature Service, or Both

    A240/A240M Specification for Chromium and Chromium-Nickel Stainless Steel Plate, Sheet, and Strip for Pressure Vessels and for General Applications

    A269 Specification for Seamless and Welded Austenitic Stainless Steel Tubing for General Service

    A276 Specification for Stainless Steel Bars and Shapes

    A312/A312M Specification for Seamless, Welded, and Heavily Cold Worked Austenitic Stainless Steel Pipes

    A354 Specification for Quenched and Tempered Alloy Steel Bolts, Studs, and Other Externally Threaded Fasteners

    A434 Specification for Steel Bars, Alloy, Hot-Wrought or Cold-Finished, Quenched and Tempered

    A449 Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength, General Use

    A563 Specification for Carbon and Alloy Steel Nuts

    A564/A564M Specification for Hot-Rolled and Cold-Finished Age-Hardening Stainless Steel Bars and Shapes

    A574 Specification for Alloy Steel Socket-Head Cap Screws

    A582/A582M Specification for Free-Machining Stainless Steel Bars

    A743/A743M Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel, Corrosion Resistant, for General Application

    A747/A747M Specification for Steel Castings, Stainless, Precipitation Hardening

    B148 Specification for Aluminum-Bronze Sand Castings

    B150/B150M Specification for Aluminum Bronze Rod, Bar, and Shapes

    B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate

    B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

    B271 Specification for Copper-Base Alloy Centrifugal Castings

    B505/B505M Specification for Copper Alloy Continuous Castings

    B584 Specification for Copper Alloy Sand Castings for General Applications

    D1418 Practice for Rubber and Rubber Latices--Nomenclature

    D2000 Classification System for Rubber Products in Automotive Applications

    D3951 Practice for Commercial Packaging

    F104 Classification System for Nonmetallic Gasket Materials

    F467 Specification for Nonferrous Nuts for General Use

    F468 Specification for Nonferrous Bolts, Hex Cap Screws, Socket Head Cap Screws, and Studs for General Use

    F593 Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs

    F594 Specification for Stainless Steel Nuts

    F837 Specification for Stainless Steel Socket Head Cap Screws

    F880 Specification for Stainless Steel Socket, Square Head, and Slotted Headless-Set Screws

    F912 Specification for Alloy Steel Socket Set Screws

    F1511 Specification for Mechanical Seals for Shipboard Pump Applications

    ANSI Standard

    B16.24 Pipe Flanges and Flanged Fittings

    ANSI/HI Standard

    3.6 Rotary Pump Tests


    ICS Code

    ICS Number Code 47.020.20 (Marine engines and propulsion systems)

    UNSPSC Code

    UNSPSC Code 40170000(Pipe piping and pipe fittings)


    DOI: 10.1520/F1718-01R13

    ASTM International is a member of CrossRef.

    ASTM F1718

    Citing ASTM Standards
    Back to Top