ASTM F1673 - 10

    Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems

    Active Standard ASTM F1673 | Developed by Subcommittee: F17.63

    Book of Standards Volume: 08.04


    Buy Standard (PDF)
    7 pages
    $42.00
    Buy Standard (Print)
    7 pages
    $42.00
    Buy Standard + Redline (PDF)
    14 pages
    $50.40

    Historical (view previous versions of standard)


    ASTM F1673

    Abstract

    This specification covers requirements for polyvinylidene drainage systems for corrosive applications. Requirements for material, pipe and fittings are included. Polyvinylidene fluoride includes emulsion/suspension polymerization and copolymers of vinylidene fluoride/hexafluoropropylene produced by either method. These requirements apply to Schedule 40 and 80 IPS and SDR 21 pipe sizes. Pipe and fittings are to be joined by heat fusion or mechanical methods. The following tests shall be performed: chemical resistance; water absorption; joint testshydrostatic pressure tests; mechanical joint pullout test; threads; flattening; and impact resistance for PVDF pipe and fittings.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers requirements for polyvinylidene fluoride drainage systems for corrosive applications. Requirements for material, pipe and fittings are included. Polyvinylidene fluoride includes emulsion/suspension polymerization and copolymers of vinylidene fluoride/hexafluoropropylene produced by either method.

    1.2 These requirements apply to Schedule 40 and 80 IPS, SDR 32.5, and SDR 21 pipe sizes. Pipe and fittings are to be joined by heat fusion or mechanical methods using the equipment supplied by the manufacturers.

    1.3 This specification is not intended to provide for interchangeability between plastic pipe and fittings from different manufacturers, but it does allow for transition fittings for joining one manufacturer's product to another's product, provided the joining technique used is other than heat fusion.

    1.4 This specification is not for polyvinylidene pressure systems.

    1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.6 Notes and appendixes are not a mandatory part of this specification.

    1.7 The following safety hazard caveat pertains only to the test method portion, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D543 Practices for Evaluating the Resistance of Plastics to Chemical Reagents

    D570 Test Method for Water Absorption of Plastics

    D618 Practice for Conditioning Plastics for Testing

    D883 Terminology Relating to Plastics

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

    D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

    D3222 Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials

    D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns

    D5575 Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers

    F412 Terminology Relating to Plastic Piping Systems

    F1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and Fittings

    Other Standard

    Uniform Plumbing Cod

    Military Standard

    MIL-STD 129 Marking for Shipment and Storage

    Federal Standard

    Fed. Std. No. 123 Marking for Shipment Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.


    ICS Code

    ICS Number Code 13.030.40 (Installations and equipment for waste disposal and treatment); 83.080.01 (Plastics in general)

    UNSPSC Code

    UNSPSC Code 40171500(Commercial pipe and piping)


    DOI: 10.1520/F1673-10

    ASTM International is a member of CrossRef.

    ASTM F1673

    Citing ASTM Standards
    Back to Top