ASTM F1533 - 01(2009)

    Standard Specification for Deformed Polyethylene (PE) Liner

    Active Standard ASTM F1533 | Developed by Subcommittee: F17.26

    Book of Standards Volume: 08.04


      Format Pages Price  
    PDF Version 4 $37.00   ADD TO CART
    Print Version 4 $37.00   ADD TO CART


    Abstract

    This specification covers requirements and test methods for deformed polyethylene (PE) liner for the rehabilitation of gravity flow and nonpressure pipelines. PE material shall conform to the recommended hydrostatic design basis. The process shall involve installing a deformed liner into an existing pipeline then reforming the liner to fit tightly to the bore of the original pipeline. Requirements and test methods that shall conform to this specification include workmanship, dimensions, size, environmental stress crack resistance, tensile strength, tensile elongation, flexural modulus, conditioning, referee testing, quality control testing, marking, and packaging.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers requirements and test methods for materials of deformed PE liner intended for the rehabilitation of gravity flow and nonpressure pipelines. This application is for municipal sewage, storm water, industrial process liquids and effluents, conduit, and ducts. This renewal process involves installing a deformed liner into an existing pipeline, conduit, or duct, then reforming the liner with heat and pressure to fit tightly to the bore of the original pipeline, conduit, or duct.

    1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. In referee decisions, inch-pound units shall be used.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D618 Practice for Conditioning Plastics for Testing

    D638 Test Method for Tensile Properties of Plastics

    D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D1693 Test Method for Environmental Stress-Cracking of Ethylene Plastics

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2837 Test Method for Obtaining Hydrostatic Design Basis for Thermoplastic Pipe Materials or Pressure Design Basis for Thermoplastic Pipe Products

    D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials

    F412 Terminology Relating to Plastic Piping Systems

    F1248 Test Method for Determination of Environmental Stress Crack Resistance (ESCR) of Polyethylene Pipe

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage

    Federal Standard

    Fed.Std.No.123 Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://dodssp.daps.dla.mil.


    ICS Code

    ICS Number Code 23.040.20 (Plastic pipes)

    UNSPSC Code

    UNSPSC Code 40171500(Commercial pipe and piping)


    DOI: 10.1520/F1533-01R09

    ASTM International is a member of CrossRef.

    ASTM F1533

    Citing ASTM Standards
    Back to Top