ASTM F1335-04

    Standard Specification for Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service (Withdrawn 2011)

    Withdrawn Standard: ASTM F1335-04 | Developed by Subcommittee: F17.11

    WITHDRAWN, NO REPLACEMENT


      Format Pages Price  
    PDF 11 $58.80   ADD TO CART


    Withdrawn Rationale:

    This specification covers pressure-rated composite pipe and fittings for the transport of hot or cold liquids, beverages, or gases that are compatible with the composite pipe and fittings.

    Formerly under the jurisdiction of Committee F17 on Plastic Piping Systems, this specification was withdrawn in November 2011 because there is no known product being manufactured per Specification F1335.

    1. Scope

    1.1 This specification covers pressure-rated composite pipe and fittings for the transport of hot or cold liquids, beverages, or gases that are compatible with the composite pipe and fittings.

    1.2 Composite pipe is produced using a butt welded aluminum pipe as a core, with an extruded inside layer of crosslinked polyethylene (PEX) or polyethylene (PE). An adhesive layer is used to bond the inside layer to the wall of the aluminum pipe. An outer layer of polyethylene (PE) and an adhesive layer are extruded to the outer wall of the aluminum pipe.

    1.3 Composite pipe is produced in four configurations and referenced in Fig. 1, as Classes 1, 2, 3, and 4 composite pipe.

    1.4 This specification includes compression fittings and compression joints, which are referenced in . Compression fittings as described in this specification are not compatible for gas transportation. Threaded fittings are referenced in .

    1.5 The following precautionary caveat pertains only to the test method portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.6 The values stated in acceptable SI units are to be regarded as the standard. The values given in parentheses are provided for information only. The values stated in each system are not exact equivalents, therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.



    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B283 Specification for Copper and Copper-Alloy Die Forgings (Hot-Pressed)

    B313/B313M Specification for Aluminum and Aluminum-Alloy Round Welded Tubes

    B547/B547M Specification for Aluminum and Aluminum-Alloy Formed and Arc-Welded Round Tube

    B584 Specification for Copper Alloy Sand Castings for General Applications

    D618 Practice for Conditioning Plastics for Testing

    D638 Test Method for Tensile Properties of Plastics

    D1248 Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable

    D1505 Test Method for Density of Plastics by the Density-Gradient Technique

    D1598 Test Methods for Time-to-Failure of Plastic Pipe Under Constant Internal Pressure

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D1898 Practice for Sampling of Plastics

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2765 Test Methods for Determination of Gel Content and Swell Ratio of Crosslinked Ethylene Plastics

    D3222 Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials

    D3350 Specification for Polyethylene Plastics Pipe and Fittings Materials

    D3418 Test Method for Transition Temperature of Polymers by Differential Scanning Calorimetry

    F412 Terminology Relating to Plastic Piping Systems

    National Sanitation Foundation (NSF) Standards

    StandardNo.61 for Drinking Water System Components--Health Effects

    ISO Standards

    ISO10508 Thermoplastics Pipe and Fittings for Hot and Cold Water Systems

    DVGW Standard

    W534 Technical Rules for Connecting Pipe Elements and Pipe Connections for Pipe in Drinking Water Installations; Requirements and Testing

    Federal Standard

    Fed.Std.No.123 Marking for Shipment (Civil Agencies)

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage


    Referencing This Standard

    DOI: 10.1520/F1335-04

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM F1335-04, Standard Specification for Pressure-Rated Composite Pipe and Fittings for Elevated Temperature Service (Withdrawn 2011), ASTM International, West Conshohocken, PA, 2004, www.astm.org

    Back to Top