ASTM F1247 - 89(2011)

    Standard Specification for Intrusion Resistant Generic Vault Structures

    Active Standard ASTM F1247 | Developed by Subcommittee: F12.10

    Book of Standards Volume: 15.08


      Format Pages Price  
    PDF 8 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 8 $43.00   ADD TO CART


    Abstract

    This specification is for the use and guidance of those who purchase, design, construct, install, approve, or modify generic vault structures intended for protection of valuables against loss due to forced entry. It also includes the descriptions of terms, classifications, materials, practices, and methods to be followed in constructing, fabricating, or modifying intrusion resistant generic vaults. The vault shall be rated as a unit and that rating shall be determined by the component having the lowest classification. The walls, floor, and ceiling of a vault shall be formed or composed of materials without true joints or seams, with the exception of cold concrete seams necessitated by construction technique. Components of a building shall not be used as part of the vault unless constructed to provide the equivalent intrusion resistance. The vault enclosure shall be classified into four types: Type M, Type 1, Type 2, and Type 3. Materials to be used in the construction of vault structures shall include concrete, concrete reinforcements, conduit, and grout.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    Significance and Use

    This specification provides guidelines for the selection of a generic vault, in accordance with its intended use.

    This specification is intended to assist users in availing themselves of various generically constructed products, while maintaining consistency with their selected intrusion-resistance level.

    This specification is not meant to recommend or prefer the use of any single product, any type level, or its application.

    1. Scope

    1.1 This specification is for the use and guidance of those who purchase, design, construct, install, approve, or modify generic vault structures intended for protection of valuables against loss due to forced entry.

    1.2 This specification includes the descriptions of terms, classifications, materials, practices, and methods to be followed in constructing, fabricating, or modifying intrusion resistant generic vaults.

    1.3 This specification does not address fire resistivity, nor does it address modular panels.

    1.4 This specification is not intended to prevent the use of systems, methods, or devices that provide a level of intrusion resistance equivalent or better than that prescribed herein. Any system, method, or device different from that detailed herein may be examined, in accordance with the intent of this specification, and if found to be equivalent or better, may be included.

    1.5 Nothing in this specification shall be construed to prohibit better or safer conditions than the requirements specified herein.

    1.6 Materials and construction details outlined in this specification are intended to detail protective requirements necessary to achieve the required level of intrusion resistance, and are not intended to address structural soundness or operational fitness, areas for which the project engineer, architect, or equipment supplier are responsible.

    1.7 Each referenced document cited in Section 2 shall be meant to be the edition in effect on the date this specification was published.

    Note 1—A rationale is given in Appendix X1.

    1.8 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.9 The following precautionary statement pertains to the test method portion only, Section 9, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A184/A184M Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement

    A615/A615M Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement

    A635/A635M Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for

    F1090 Classification for Bank and Mercantile Vault Construction


    ICS Code

    ICS Number Code 13.310 (Protection against crime)

    UNSPSC Code

    UNSPSC Code 92121700(Security systems services)


    Referencing This Standard

    DOI: 10.1520/F1247-89R11

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM F1247-89(2011), Standard Specification for Intrusion Resistant Generic Vault Structures, ASTM International, West Conshohocken, PA, 2011, www.astm.org

    Back to Top