You are being redirected because this document is part of your ASTM Compass® subscription.
    This document is part of your ASTM Compass® subscription.

    ASTM E2950 - 14

    Standard Specification for Metal Canopy Systems

    Active Standard ASTM E2950 | Developed by Subcommittee: E54.05

    Book of Standards Volume: 15.08


      Format Pages Price  
    PDF 6 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 6 $43.00   ADD TO CART


    Abstract

    This specification applies to metal canopy systems including structural framing, canopy deck system, drainage system, fascia panels, accessories and trim, and canopy concrete foundations and accessories. It specifies the requirements for pre-engineered metal canopy systems, manufacturer's standard mutually dependent components, and assemblies that form a pre-engineered overhead canopy system to enhance safety and security. The pre-engineered overhead canopy system shall be capable of withstanding required design loads per the International Building Code as adopted or modified by local jurisdictions, thermally induced movement, and exposure to weather without failure. Primary structural frame design shall include fixed-base columns capable of transferring moments and forces into foundations, as well as roof purlins, main frame beams, and tube columns, plus secondary framing, canopy deck and fascia panels, and accessories. The requirements also cover submittals; delivery, storage, and handling; coordination; and warranty. Erection of structural steel, canopy deck panel installation, fascia installation, accessory installation, and cleaning and protection are also covered by this specification.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification includes the following:

    1.1.1 Structural framing,

    1.1.2 Canopy Deck System,

    1.1.3 Drainage system,

    1.1.4 Fascia panels,

    1.1.5 Accessories and trim, and

    1.1.6 Canopy concrete foundations and accessories.

    1.2 Units—The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A36/A36M Specification for Carbon Structural Steel

    A500/A500M Specification for Cold-Formed Welded and Seamless Carbon Steel Structural Tubing in Rounds and Shapes

    A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

    A775/A775M Specification for Epoxy-Coated Steel Reinforcing Bars

    A992/A992M Specification for Structural Steel Shapes

    A1011/A1011M Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon, Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, and Ultra-High Strength

    C1107/C1107M Specification for Packaged Dry, Hydraulic-Cement Grout (Nonshrink)


    ICS Code

    ICS Number Code 91.060.20 (Roofs)

    UNSPSC Code

    UNSPSC Code 30151902(Canopy)


    Referencing This Standard

    DOI: 10.1520/E2950-14

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM E2950-14, Standard Specification for Metal Canopy Systems, ASTM International, West Conshohocken, PA, 2014, www.astm.org

    Back to Top