ASTM D7533/D7533M-09

    Standard Practice for Minimum Geospatial Data for Abandoned Mine Land Problem Area (Withdrawn 2013)

    Withdrawn Standard: ASTM D7533/D7533M-09 | Developed by Subcommittee: D18.01

    WITHDRAWN, REPLACED BY D7699/D7699M


      Format Pages Price  
    PDF Version 7 $50.40   ADD TO CART

    Active (view current version of standard)

    ASTM License Agreement


    Withdrawn Rationale:

    This practice covers the minimum elements for the accurate description of data for defining an Abandoned Mine Land Inventory System (AMLIS) Problem Area (PA). Formerly under the jurisdiction of Committee D18 on Soil and Rock, this practice was withdrawn in January 2013 and replaced by Practice D7699/D7699M for Minimum Geospatial Data for Abandoned Mine Land Problem Areas, Planning Units, Keyword Features, and Project Sites.

    1. Scope

    1.1 This practice covers the minimum elements for the accurate description of data for defining an Abandoned Mine Land Inventory System (AMLIS) Problem Area (PA).

    1.1.1 This practice addresses mining geospatial data relative to the Surface Mining Control and Reclamation Act of 1977 (SMCRA). This geospatial data shall be obtained from each state, tribal, or federal (or combinations thereof) coal mining regulatory authority (RA) authorized under SMCRA to reclaim the surface and underground effects of past mining operations. Abandoned mine land (AML), as specified in SMCRA Sections 404 (coal), 409 and 411 (non-coal) and cross referenced in additional sections on eligible lands, consists of those lands and waters which were mined for coal or other minerals (or both), or impacted by processing operations prior to enactment of the SMCRA and abandoned or left in an inadequate condition of reclamation, and for which there is no continuing reclamation responsibility under state or other federal laws for mitigation of adverse impacts to human health and safety or environmental resources.

    1.1.2 Title IV of the SMCRA establishes the national AML Reclamation Program under the Office of Surface Mining Reclamation and Enforcement (OSMRE), U.S. Department of the Interior. The program was developed to reclaim land and water resources adversely affected by past coal mining and left abandoned or inadequately restored. During the years immediately following enactment of the SMCRA, OSMRE, states, and Native American tribes conducted surveys of eligible lands and waters and created individual inventories of problems to be addressed under Title IV. In 1990 SMCRA was amended and OSMRE was required to maintain a national inventory of high priority abandoned coal sites and provide standardized procedures for states and tribes to use in updating the data. The need for an automated nationwide inventory system led to the creation of the national AMLIS, a compilation of the individual state, tribe, Federal Reclamation Program (FRP), and Rural Abandoned Mine Program (RAMP) inventories. The AMLIS documents the estimated unfunded costs to remedy AML problems, records when funding is made available for a PA, and captures completed costs for constructed projects. It is used to record the work completed under each individual AML program and report the extent and cost of AML problems remaining.

    1.1.3 As used in this practice, an AML PA represents a closed polygon that defines the boundary of a uniquely defined geographic area contained within an AML Planning Unit (PU) as described in the AML Inventory Manual. An AML PA is a subdivision of an AML PU that contains one or more AML problem type keyword features together with adjacent or hydrologically connected and impacted land and water resources. An AML PA should not cross PU boundaries.

    1.2 This practice applies to pre-SMCRA AML PAs that are inventoried in the AMLIS under the SMCRA Title IV Reauthorization to provide for identification and management of AML sites and reclamation operations and facilitate the sharing of information with the public.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.5 This practice offers a set of instructions for performing one or more specific operations. This document cannot replace education or experience and should be used in conjunction with professional judgment. Not all aspects of this practice may be applicable in all circumstances. This ASTM standard is not intended to represent or replace the standard of care by which the adequacy of a given professional service must be judged, nor should this document be applied without consideration of a projects many unique aspects. The word Standard in the title of this document means only that the document has been approved through the ASTM consensus process.



    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D653 Terminology Relating to Soil, Rock, and Contained Fluids

    D5254 Practice for Minimum Set of Data Elements to Identify a Ground-Water Site

    D5911 Practice for Minimum Set of Data Elements to Identify a Soil Sampling Site

    ANSI Standards

    INCITS320-1998 (R2003) Information technology-Spatial Data Transfer

    Federal Geographic Data Committee Standards

    Project1574-D Information Technology--geographic information framework data content standard, Part 5 governmental unit and other geographic area boundaries


    DOI: 10.1520/D7533_D7533M-09

    ASTM International is a member of CrossRef.