| ||Format||Pages||Price|| |
|35||$62.00||  ADD TO CART|
|Hardcopy (shipping and handling)||35||$62.00||  ADD TO CART|
|Standard + Redline PDF Bundle||70||$74.40||  ADD TO CART|
This specification establishes the manufacture, property requirements, and testing of several grades of laminated thermosetting materials consisting of two or more plies or layers of reinforcing material such as cellulose paper, cotton fabric, glass fabric, and synthetic fiber fabrics, bonded by a thermosetting synthetic resin. These materials are available in the form of sheets, rolled and molded tubes, and molded rods.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers laminated thermosetting materials consisting of two or more plies or layers of reinforcing material bonded by a thermosetting synthetic resin. Examples of such reinforcement are cellulose paper, cotton fabric, glass fabric, and synthetic fiber fabrics. These materials are available in the form of sheets, rolled and molded tubes, and molded rods.
1.2 The values stated in inch-pound units are to be regarded as the standard.
1.3 The following safety hazards caveat pertains only to the test methods described in this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
Federal SpecificationsL-P-509 Plastic Sheet, Rod and Tube, Laminated Thermosetting L-P-513 Plastic Sheet and Insulation Sheet, Electrical (Laminated, Thermosetting, Paper-Base, Phenolic-Resin)
IEC StandardPublication60893-3 Specification for Industrial Laminated Sheets Based on Thermosetting Resins for Electrical Purposes Available from American National Standards Institute (ANSI), 25 W. 43rd St., 4th Floor, New York, NY 10036, http://www.ansi.org.
IEEE Standards1 General Principles for Temperature Limits in the Rating of Electric Equipment 101 Guide for the Statistical Analysis of Thermal Life Test Data 98 Guide for the Preparation of Test Procedures for the Thermal Evaluation and Establishment of Temperature Indices of Solid Electrical Insulating Materials 99 Guide for the Preparation of Test Procedures for the Thermal Evaluation of Insulation Systems for Electric Equipment
NEMA StandardsLI 1-1971 Industrial Laminated Thermosetting Products LI 3-1961 High-Temperature Properties of Industrial Thermosetting Laminates LI 5-1969 Temperature Indices of Industrial Thermosetting Laminates
D229 Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation
D257 Test Methods for DC Resistance or Conductance of Insulating Materials
D348 Test Methods for Rigid Tubes Used for Electrical Insulation
D349 Test Methods for Laminated Round Rods Used for Electrical Insulation
D495 Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation
D621 Specification for Jute Rove and Plied Yarn for Electrical and Packing Purposes
D668 Test Methods of Measuring Dimensions of Rigid Rods and Tubes Used for Electrical Insulation
D883 Terminology Relating to Plastics
D1180 Method of Test for Warpage of Sheet Plastics
D1711 Terminology Relating to Electrical Insulation
D2303 Test Methods for Liquid-Contaminant, Inclined-Plane Tracking and Erosion of Insulating Materials
D2304 Test Method for Thermal Endurance of Rigid Electrical Insulating Materials
D3636 Practice for Sampling and Judging Quality of Solid Electrical Insulating Materials
D6054 Practice for Conditioning Electrical Insulating Materials for Testing
Military SpecificationsMIL-P-15035 Plastic Sheet, Laminated, Thermosetting, Cotton-Fabric-Base, Phenolic-Resin MIL-P-15037 Plastic Sheet, Laminated, Thermosetting, Glass-Cloth, Melamine-Resin MIL-P-15047 Plastic Material, Laminated Thermosetting Sheets, Nylon Fabric Base, Phenolic-Resin MIL-P-18177 Plastic Sheet, Laminated, Thermosetting, Glass Fibre Base, Epoxy-Resin MIL-P-22324 Plastic Sheet, Thermosetting, Paper-Base, Epoxy-Resin MIL-P-997 Plastic Material, Laminated, Thermosetting, Electric Insulation, Sheets, Glass Cloth, Silicone Resin
ICS Number Code 83.140.20 (Laminated sheets)
ASTM D709-13, Standard Specification for Laminated Thermosetting Materials, ASTM International, West Conshohocken, PA, 2013, www.astm.orgBack to Top