ASTM D6754 / D6754M - 10

    Standard Specification for Ketone Ethylene Ester Based Sheet Roofing

    Active Standard ASTM D6754 / D6754M | Developed by Subcommittee: D08.18

    Book of Standards Volume: 04.04


    Buy Standard (PDF)
    4 pages
    $37.00
    Buy Standard (Print)
    4 pages
    $37.00
    Buy Standard + Redline (PDF)
    8 pages
    $44.40

    Historical (view previous versions of standard)


    ASTM D6754 / D6754M

    Abstract

    This specification covers flexible sheet made from ketone ethylene ester (KEE) as the primary polymer intended for use in single ply roofing membrane exposed to the weather. The sheet shall be reinforced with fabric. The sheet shall be formulated from the appropriate polymers and other compounding ingredients. To make seam and repairs, the sheet shall be capable of being bonded watertight to itself during the design service life of the sheets. Overall thickness; thickness, coating over reinforcement optical method; breaking strength; elongation at break; tearing strength; linear dimensional change; fabric adhesion; heat aging; after heat aging low temperature bend; low temperature bend; water absorption; factory seam strength; hydrostatic resistance; static puncture test; accelerated weathering test; fungi resistance; abrasion test; and dimension tests shall be performed to conform with the requirements specified.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers flexible sheet made from ketone ethylene ester (KEE) as the primary polymer intended for use in single ply roofing membrane exposed to the weather. The sheet shall be reinforced with fabric.

    1.2 In-place roof system design criteria, such as fire resistance, field-seaming strength, material compatibility, uplift resistance, in-situ shrinkage, among others, are factors that must be considered, but are beyond the scope of this specification.

    1.3 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.4 The following precautionary caveat pertains to the test methods portion only, Section 8, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D471 Test Method for Rubber Property--Effect of Liquids

    D751 Test Methods for Coated Fabrics

    D1079 Terminology Relating to Roofing and Waterproofing

    D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature

    D2136 Test Method for Coated Fabrics--Low-Temperature Bend Test

    D3045 Practice for Heat Aging of Plastics Without Load

    D3389 Test Method for Coated Fabrics Abrasion Resistance (Rotary Platform Abrader)

    D5602 Test Method for Static Puncture Resistance of Roofing Membrane Specimens

    D5635 Test Method for Dynamic Puncture Resistance of Roofing Membrane Specimens

    G21 Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi

    G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources

    G154 Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials

    G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials


    ICS Code

    ICS Number Code 91.060.20 (Roofs)

    UNSPSC Code

    UNSPSC Code 30151500(Roofing materials)


    DOI: 10.1520/D6754_D6754M-10

    ASTM International is a member of CrossRef.

    ASTM D6754 / D6754M

    Citing ASTM Standards
    Back to Top