| ||Format||Pages||Price|| |
|3||$39.00||  ADD TO CART|
|Hardcopy (shipping and handling)||3||$39.00||  ADD TO CART|
|Standard + Redline PDF Bundle||6||$46.80||  ADD TO CART|
This specification covers a liquid-applied solvent dispersed elastomeric coating used as a roofing membrane for spray polyurethane foam (SPF) insulation whose principal polymer in the dispersion contains more than 95 % silicone. The product, as manufactured, shall be in liquid form for application to SPF surfaces by brushing, squeegeeing, rolling, or spraying. The product shall be composed of dispersion containing as the principal polymer more than 95 % silicone polymers to which various pigments and other additives have been added to give the required physical properties. Liquid properties like viscosity, volume solids, and weight solids shall be determined after conducting different tests. Physical properties of cured silicone coating like elongation, tensile strength, permeance, accelerated weathering, adhesion, tear resistance, and low-temperature flexibility shall be determined after a series of tests.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1.1 This specification covers a liquid-applied solvent dispersed elastomeric coating used as a roofing membrane for spray polyurethane foam (SPF) insulation whose principal polymer in the dispersion contains more than 95 % silicone.
1.2 This specification does not provide guidance for application.
1.3 The following precautionary caveat pertains only to the test method portions, Sections and .
1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.
1.5 This standard may involve hazardous materials, operations, and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory requirements prior to use.
2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.
D16 Terminology for Paint, Related Coatings, Materials, and Applications
D522 Test Methods for Mandrel Bend Test of Attached Organic Coatings
D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers
D903 Test Method for Peel or Stripping Strength of Adhesive Bonds
D1079 Terminology Relating to Roofing and Waterproofing
D1644 Test Methods for Nonvolatile Content of Varnishes
D2196 Test Methods for Rheological Properties of Non-Newtonian Materials by Rotational (Brookfield type) Viscometer
D2370 Test Method for Tensile Properties of Organic Coatings
D2697 Test Method for Volume Nonvolatile Matter in Clear or Pigmented Coatings
D4798 Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)
E96/E96M Test Methods for Water Vapor Transmission of Materials
ICS Number Code 83.100 (Cellular materials); 91.060.20 (Roofs)
UNSPSC Code 30151500(Roofing materials); 13111300(Foams)
|Link to Active (This link will always route to the current Active version of the standard.)|
ASTM D6694 / D6694M-15, Standard Specification for Liquid-Applied Silicone Coating Used in Spray Polyurethane Foam Roofing Systems, ASTM International, West Conshohocken, PA, 2015, www.astm.orgBack to Top