ASTM D5751 - 99(2012)

    Standard Specification for Adhesives Used for Laminate Joints in Nonstructural Lumber Products

    Active Standard ASTM D5751 | Developed by Subcommittee: D14.30

    Book of Standards Volume: 15.06


    Buy Standard (PDF)
    11 pages
    $48.00
    Buy Standard (Print)
    11 pages
    $48.00

    Historical (view previous versions of standard)


    ASTM D5751

    Abstract

    This specification covers performance levels for adhesives to be used in laminate joints in nonstructural lumber products. Such products include, but are not limited to, interior and exterior mouldings, window and door components or parts, and bonded lumber panels. This specification is to be used to evaluate adhesives as well as the adhesive bonds in nonstructural-glued-lumber products. Dry test, soak test, elevated temperature test, boil test, and vacuum pressure test shall be performed to meet the requirements prescribed. The precision and bias of exposure condition shall be tested to meet the requirements prescribed.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers performance levels for adhesives to be used in laminate joints in nonstructural lumber products. Such products include, but are not limited to, interior and exterior mouldings, window and door components or parts, and bonded lumber panels. This specification is to be used to evaluate adhesives as well as the adhesive bonds in nonstructural-glued-lumber products.

    Note 1This specification supersedes the laminate-joint portion of Specification D3110.
    Note 2See 3.2.1 and 3.2.2 for descriptions of a dry-use-nonstructural adhesive and a wet-use-nonstructural adhesive.

    1.2 This specification applies to laminate-joint specimens made under both laboratory and field conditions. See Section 4 for limitations in using this specification to evaluate industrially manufactured laminate joint products.

    1.3 The following safety caveat applies only to the apparatus and test methods portions, Sections 6, 7, 8, and 9 of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    1.4 The values stated in inch-pound units are to be regarded as standard.

    1.5 In this specification, laminate joint refers to both face and edge joints.

    1.6 The following index is provided as a guide to the test methods in this specification:

     

    Section

    Apparatus

     6

    Conditioning

     7

    Material and Preparation of Assemblies and  Specimens

     8

    Exposure Conditions and Treatments

     9

    Testing, Calculation, and Reporting

    10


    Note 3The conditioning needed for various stages in the preparation of the specimens and for the exposure tests are given in Sections 7, 8, and 9.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D905 Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading

    D907 Terminology of Adhesives

    D2016 Methods of Test for Moisture Content of Wood

    D2555 Practice for Establishing Clear Wood Strength Values

    D3110 Specification for Adhesives Used in Laminate Joints for Nonstructural Glued Lumber Products

    D5266 Practice for Estimating the Percentage of Wood Failure in Adhesive Bonded Joints

    E4 Practices for Force Verification of Testing Machines

    E6 Terminology Relating to Methods of Mechanical Testing

    E41 Terminology Relating To Conditioning

    E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method


    ICS Code

    ICS Number Code 83.180 (Adhesives)

    UNSPSC Code

    UNSPSC Code 11122000(Engineered wood products); 31201601(Chemical adhesives)


    DOI: 10.1520/D5751-99R12

    ASTM International is a member of CrossRef.

    ASTM D5751

    Citing ASTM Standards
    Back to Top