ASTM D5363 - 03(2008)

    Standard Specification for Anaerobic Single-Component Adhesives (AN)

    Active Standard ASTM D5363 | Developed by Subcommittee: D14.60

    Book of Standards Volume: 15.06


      Format Pages Price  
    PDF 11 $48.00   ADD TO CART
    Hardcopy (shipping and handling) 11 $48.00   ADD TO CART
    Standard + Redline PDF Bundle 22 $57.60   ADD TO CART


    Abstract

    This specification establishes the requirements for single-component anaerobic adhesives suitable for locking, sealing, and retaining threaded or cylindrical assemblies. It is intended to be a means of classifying the adhesives, and does not address engineering design purposes. The adhesives are cured to a solid state when confined between closely fitting active metal surfaces. Materials shall undergo test procedures and conform accordingly to the following requirements: ultraviolet fluorescence; color and workmanship; flash point; storage stability; toxicity; solvent resistance; hot strength; heat aging; cold strength; lubricity; fluid tightness; wicking; viscosity; speed of cure; prevailing torque strength (strength at standard conditions); and qualification of primers.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    Significance and Use

    1. Scope

    1.1 This specification covers single-component anaerobic adhesives suitable for locking, sealing, and retaining threaded or cylindrical assemblies. The adhesives are cured to a solid state when confined between closely fitting active metal surfaces.

    1.2 This specification is intended to be a means of classifying anaerobic adhesives. It is not intended for engineering design purposes.

    1.3 This specification is intended to replace Military Specifications MIL-S-22473, MIL-S-46163, and MIL-R-46082.

    1.4 The values stated in SI units are to be regarded as the standard.

    1.5 The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A109/A109M Specification for Steel, Strip, Carbon (0.25 Maximum Percent), Cold-Rolled

    B36/B36M Specification for Brass Plate, Sheet, Strip, And Rolled Bar

    B209 Specification for Aluminum and Aluminum-Alloy Sheet and Plate

    B633 Specification for Electrodeposited Coatings of Zinc on Iron and Steel

    D56 Test Method for Flash Point by Tag Closed Cup Tester

    D439 Specification for Automotive Gasoline

    D445 Test Method for Kinematic Viscosity of Transparent and Opaque Liquids (and Calculation of Dynamic Viscosity)

    D770 Specification for Isopropyl Alcohol

    D907 Terminology of Adhesives

    D1084 Test Methods for Viscosity of Adhesives

    D1193 Specification for Reagent Water

    D2693 Specification for Ethylene Glycol

    D3951 Practice for Commercial Packaging

    D4562 Test Method for Shear Strength of Adhesives Using Pin-and-Collar Specimen

    D4800 Guide for Classifying and Specifying Adhesives

    D5648 Test Method for Torque-Tension Relationship of Adhesives Used on Threaded Fasteners (Lubricity)

    D5649 Test Method for Torque Strength of Adhesives Used on Threaded Fasteners

    D5657 Test Method for Fluid Tightness Ability of Adhesives Used on Threaded Fasteners

    E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process

    Military Standards

    MIL-STD-118 Commercial Packaging of Supplies and Equipment

    Federal Standards

    FED-STD-313 Material Safety Data Sheets, Preparation and Submission of

    Federal Specifications

    QQ-P-416 Plating, Cadmium, Electrodeposited


    ICS Code

    ICS Number Code 83.180 (Adhesives)

    UNSPSC Code

    UNSPSC Code 31201601(Chemical adhesives)


    DOI: 10.1520/D5363-03R08

    ASTM International is a member of CrossRef.

    ASTM D5363

    Citing ASTM Standards
    Back to Top