ASTM D5329 - 16

    Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements

    Active Standard ASTM D5329 | Developed by Subcommittee: D04.33

    Book of Standards Volume: 04.03


      Format Pages Price  
    PDF 9 $45.00   ADD TO CART
    Hardcopy (shipping and handling) 9 $45.00   ADD TO CART
    Standard + Redline PDF Bundle 18 $54.00   ADD TO CART


    Significance and Use

    3.1 These test methods describe procedures for determining specification conformance for hot-applied, field-molded joint and crack sealants and fillers.

    1. Scope

    1.1 These test methods cover tests for hot-applied types of joint and crack sealants and fillers for portland cement concrete and asphaltic concrete pavements. There are numerous standard material specifications that use these test methods. Refer to the respective standard material specification of interest to determine which of the following test methods to use. For sample melting and concrete block preparation see their respective standard practices.

    1.2 The test methods appear in the following sections:

     

    Section

    Artificial Weathering 

    13

    Asphalt Compatibility 

    12

    Bond, Non-Immersed 

    8

    Bond, Water-Immersed 

    9

    Cone Penetration, Non-Immersed 

    6

    Flexibility 

    15

    Flow 

    7

    Resilience 

    10

    Resilience, Oven-Aged 

    11

    Tensile Adhesion 

    14

    1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D5 Test Method for Penetration of Bituminous Materials

    D217 Test Methods for Cone Penetration of Lubricating Grease

    D618 Practice for Conditioning Plastics for Testing

    D1074 Test Method for Compressive Strength of Bituminous Mixtures

    D1561 Practice for Preparation of Bituminous Mixture Test Specimens by Means of California Kneading Compactor

    D1985 Practice for Preparing Concrete Blocks for Testing Sealants, for Joints and Cracks

    D3381 Specification for Viscosity-Graded Asphalt Cement for Use in Pavement Construction

    D5167 Practice for Melting of Hot-Applied Joint and Crack Sealant and Filler for Evaluation

    D6690 Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements

    E145 Specification for Gravity-Convection and Forced-Ventilation Ovens

    G151 Practice for Exposing Nonmetallic Materials in Accelerated Test Devices that Use Laboratory Light Sources

    G154 Practice for Operating Fluorescent Ultraviolet (UV) Lamp Apparatus for Exposure of Nonmetallic Materials

    G155 Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials


    UNSPSC Code

    UNSPSC Code 30111509(Asphalt based concrete); 31201600(Other adhesives and sealants)


    Referencing This Standard
    Link Here
    Link to Active (This link will always route to the current Active version of the standard.)

    DOI: 10.1520/D5329-16

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM D5329-16, Standard Test Methods for Sealants and Fillers, Hot-Applied, for Joints and Cracks in Asphalt Pavements and Portland Cement Concrete Pavements, ASTM International, West Conshohocken, PA, 2016, www.astm.org

    Back to Top