ASTM D5147 / D5147M - 14

    Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material

    Active Standard ASTM D5147 / D5147M | Developed by Subcommittee: D08.04

    Book of Standards Volume: 04.04


      Format Pages Price  
    PDF 8 $42.00   ADD TO CART
    Hardcopy (shipping and handling) 8 $42.00   ADD TO CART
    Standard + Redline PDF Bundle 16 $50.40   ADD TO CART


    Abstract

    These test methods cover procedures for sampling and testing prefabricated, reinforced, polymer-modified bituminous sheet materials designed for single- or multiple-ply application in roofing and waterproofing membranes. From each shipment or fraction thereof, select at random a number of rolls equal to one half the cube root of the total number of rolls in the lot. If the calculated number is fractional, express it as the next highest whole number. The load strain (tensile elongation and strain energy) properties shall be tested to meet the requirements prescribed. The tensile tear strength, moisture content, and water absorption of polymer-modified bituminous sheets shall be tested to meet the requirements prescribed. The dimensional stability, low-temperature flexibility, heat conditioning, and accelerated weathering of the polymer-modified bituminous sheets shall be tested to meet the requirements prescribed. The granule embedment, compound stability, coating thickness, low temperature unrolling, and precision and bias of the polymer-modified bituminous sheet materials shall be tested to meet the requirements prescribed.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    Significance and Use

    3.1 These test methods are used for sampling and testing modified bitumen sheet materials. Property requirements, determined by these test methods, are found in the following product standards: Specifications D6162, D6163, D6164, D6222, D6223, D6298, and D6509.

    1. Scope

    1.1 These test methods cover procedures for sampling and testing prefabricated, reinforced, polymer-modified bituminous sheet materials designed for single- or multiple-ply application in roofing and waterproofing membranes. These products may use various surfacing materials on one side.

    1.2 These test methods cover a number of different products. Not all tests are required for every product. Only those called out in the Product Standard are required.

    1.3 These test methods appear in the following order:

     

    Section

     

     

    Sampling

    4

    Conditioning

    5

    Thickness

    6

    Load Strain Properties

    7

    Tear Strength

    8

    Moisture Content

    9

    Water Absorption

    10

    Dimensional Stability

    11

    Low-Temperature Flexibility

    12

    Heat Conditioning

    13

    Accelerated Weathering

    14

    Granule Embedment

    15

    Compound Stability

    16

    Coating Thickness

    17

    Low Temperature Unrolling

    18

    Precision and Bias

    19


    1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation

    D146 Test Methods for Sampling and Testing Bitumen-Saturated Felts and Woven Fabrics for Roofing and Waterproofing

    D1204 Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature

    D4073 Test Method for Tensile-Tear Strength of Bituminous Roofing Membranes

    D4798 Practice for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)

    D4977 Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion

    D5636 Test Method for Low Temperature Unrolling of Felt or Sheet Roofing and Waterproofing Materials

    D5869 Practice for Dark Oven Heat Exposure of Roofing and Waterproofing Materials

    D6162 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

    D6163 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements

    D6164 Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Polyester Reinforcements

    D6222 Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements

    D6223 Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements

    D6298 Specification for Fiberglass Reinforced Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface

    D6509 Specification for Atactic Polypropylene (APP) Modified Bituminous Base Sheet Materials Using Glass Fiber Reinforcement

    E177 Practice for Use of the Terms Precision and Bias in ASTM Test Methods

    E691 Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method


    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    UNSPSC Code

    UNSPSC Code 30121500(Bituminous derivatives)


    DOI: 10.1520/D5147_D5147M

    ASTM International is a member of CrossRef.

    ASTM D5147 / D5147M

    Citing ASTM Standards
    Back to Top