ASTM D4067 - 11

    Standard Classification System for and Basis for Specification for Reinforced and Filled Poly(Phenylene Sulfide) (PPS) Injection Molding and Extrusion Materials Using ASTM Methods

    Active Standard ASTM D4067 | Developed by Subcommittee: D20.15

    Book of Standards Volume: 08.02


      Format Pages Price  
    PDF 5 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $43.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $51.60   ADD TO CART


    Abstract

    This classification system covers reinforced and filled poly(phenylene sulfide) (PPS) materials suitable for injection molding and extrusion. This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to be used for the manufacture of parts. The physical properties of the materials must meet the required tensile strength, flexural modulus, Izod impact strength, flexural strength, and density.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This classification system covers reinforced and filled poly(phenylene sulfide) materials suitable for injection molding and extrusion.

    1.2 This classification system is not intended for the selection of materials, but only as a means to call out plastic materials to be used for the manufacture of parts. The selection of these materials shall be made by personnel with expertise in the plastics field where the environment, inherent properties of the materials, performance of the parts, part design, manufacturing process, and economics are considered.

    1.3 The properties included in this classification system are those required to identify the compositions covered. If necessary, other requirements identifying particular characteristics important to specific applications shall be designated by using the suffixes given in Section 5 or Classification System D4000.

    1.4 The values stated in SI units are to be regarded as the standard.

    1.5 This precautionary statement pertains only to the test method portion of this classification system, Section 12. This standard does not purport to address all of the safety concerns associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

    Note 1—There is no known ISO equivalent to this standard.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D256 Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics

    D618 Practice for Conditioning Plastics for Testing

    D638 Test Method for Tensile Properties of Plastics

    D648 Test Method for Deflection Temperature of Plastics Under Flexural Load in the Edgewise Position

    D790 Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

    D792 Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement

    D883 Terminology Relating to Plastics

    D1238 Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D3418 Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry

    D3641 Practice for Injection Molding Test Specimens of Thermoplastic Molding and Extrusion Materials

    D3835 Test Method for Determination of Properties of Polymeric Materials by Means of a Capillary Rheometer

    D3892 Practice for Packaging/Packing of Plastics

    D4000 Classification System for Specifying Plastic Materials

    D5630 Test Method for Ash Content in Plastics

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E595 Test Method for Total Mass Loss and Collected Volatile Condensable Materials from Outgassing in a Vacuum Environment

    E662 Test Method for Specific Optical Density of Smoke Generated by Solid Materials

    Military Standards

    MIL-M-24519 Molding Plastics, Electrical, Thermoplastic

    ISO Standard

    ISO527–2 Plastics--Determination of Tensile Properties--Part 2: Test Conditions for Moulding and Extrusion Plastics


    ICS Code

    ICS Number Code 83.120 (Reinforced plastics)

    UNSPSC Code

    UNSPSC Code 13111000(Resins)


    DOI: 10.1520/D4067-11

    ASTM International is a member of CrossRef.

    ASTM D4067

    Citing ASTM Standards
    Back to Top