ASTM D3462 / D3462M - 10a

    Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules

    Active Standard ASTM D3462 / D3462M | Developed by Subcommittee: D08.02

    Book of Standards Volume: 04.04


      Format Pages Price  
    PDF 5 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $43.00   ADD TO CART
    Standard + Redline PDF Bundle 10 $51.60   ADD TO CART


    Abstract

    This specification deals with the standards for asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surface on the weather side with minerals. Physical requirements of the shingles such as behavior on melting, tear strength, wind resistance, fire resistance, softening point, and pliability shall be measured immediately after packaging or at a reasonable time. Physical and performance requirements after application and during in-service use are however beyond the scope of this specification.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers asphalt roofing in shingle form, composed of glass felt or felts impregnated and coated on both sides with asphalt, and surfaced on the weather side with mineral granules. This specification is designed for the evaluation of products as manufactured. The test methods, physical requirements, and minimum masses are to be measured immediately after packaging or at a reasonable time, as agreed upon between buyer and seller, after manufacture and before installation. Physical and performance requirements after application and during in-service use of the products described herein are beyond the scope of this material specification.

    1.2 Shingles meeting this specification are intended to be applied with a headlap of not less than 51 mm (2 in.).

    1.3 The shingles shall be supplied with a factory-applied self-sealing adhesive or be designed to be locked together during installation of the shingles.

    1.4 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    1.5 The following safety hazards caveat pertains only to the test method described in this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D5 Test Method for Penetration of Bituminous Materials

    D36 Test Method for Softening Point of Bitumen (Ring-and-Ball Apparatus)

    D228 Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing

    D1079 Terminology Relating to Roofing and Waterproofing

    D1922 Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method

    D3161 Test Method for Wind-Resistance of Asphalt Shingles (Fan-Induced Method)

    D4977 Test Method for Granule Adhesion to Mineral Surfaced Roofing by Abrasion

    E108 Test Methods for Fire Tests of Roof Coverings


    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    UNSPSC Code

    UNSPSC Code 30121601(Asphalt)


    Referencing This Standard

    DOI: 10.1520/D3462_D3462M-10A

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM D3462 / D3462M-10a, Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules, ASTM International, West Conshohocken, PA, 2010, www.astm.org

    Back to Top