Withdrawn Rationale:
These test methods cover procedures for sampling and testing emulsified bitumens used in relatively thick films as protective coatings for metals, built-up roofs, and bituminous pavements.
Formerly under the jurisdiction of Committee D08 on Roofing and Waterproofing, these test methods were withdrawn in July 2012 in accordance with section 10.5.3.1 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.
1. Scope
1.1 These test methods cover procedures for sampling and testing emulsified bitumens used in relatively thick films as protective coatings for metals, built-up roofs, and bituminous pavements.
1.2 The test methods appear in the following order:
| Test Procedures for All Coatings | Section |
| Sampling | 4 |
| Uniformity | 5 |
| Resistance to Freezing | 6 |
| Weight per Gallon | 7 |
| Residue by Evaporation | 8 |
| Volatiles | 9 |
| Ash Content | 10 |
| Water Content | 11 |
| Flash Point | 12 |
| Drying Time | 13 |
| Resistance to Heat | 14 |
| Resistance to Water | 15 |
| Flexibility | 16 |
| Tests used primarily for coatings used over metals and built-up roofs |
| Brush-Application Behavior | 17 |
| Spray-Application Behavior | 18 |
| Wet Flow | 19 |
| Direct Flame Test | 20 |
| Solubility of Residue in Trichloroethylene | 21 |
| Tests used primarily for coatings used over bituminous pavements |
| Wet Film Continuity | 22 |
| Resistance to Volatilization | 23 |
| Solubility of Residue in Carbon Disulfide | 24 |
| Resistance to Kerosine | 25 |
| Resistance to Impact | 26 |
| Resistance to Impact After Accelerated Weathering | 27 |
| Aggregate (Sand) Content in Bituminous Emulsions | 28 |
| Precision Bias | 29 |
1.3 The values stated in SI units are to be regarded as standard. The values in parentheses are for information only.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) 
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
C67 Test Methods of Sampling and Testing Brick and Structural Clay Tile
C670 Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials
D4 Test Method for Bitumen Content
D93 Test Methods for Flash Point by Pensky-Martens Closed Cup Tester
D95 Test Method for Water in Petroleum Products and Bituminous Materials by Distillation
D140 Practice for Sampling Bituminous Materials
D609 Practice for Preparation of Cold-Rolled Steel Panels for Testing Paint, Varnish, Conversion Coatings, and Related Coating Products
D3699 Specification for Kerosine
D4798 Test Method for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Xenon-Arc Method)
D4799 Test Method for Accelerated Weathering Test Conditions and Procedures for Bituminous Materials (Fluorescent and UV Condensation Method)
E145 Specification for Gravity-Convection and Forced-Ventilation Ovens
Keywords
ashpalt; bitumen; coal tar; coating; emulsified;
DOI: 10.1520/D2939-03
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
