ASTM D2751-05

    Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014)

    Withdrawn Standard: ASTM D2751-05 | Developed by Subcommittee: F17.62

    WITHDRAWN, NO REPLACEMENT


      Format Pages Price  
    PDF 6 $51.60   ADD TO CART


    Withdrawn Rationale:

    This specification covers acrylonitrile-butadienestyrene (ABS) sewer pipe, produced by single extrusion or simultaneous multiple coextrusion. This specification also covers fittings. Included are requirements and test methods for materials, dimensions, workmanship, chemical resistance, water resistance, and joint tightness. A form of marking to indicate compliance with this specification is also included.

    Formerly under the jurisdiction of Committee F17 on Plastic Piping Systems, this specification was withdrawn in January 2014 in accordance with section 10.6.3 of the Regulations Governing ASTM Technical Committees, which requires that standards shall be updated by the end of the eighth year since the last approval date.

    1. Scope

    1.1 This specification covers acrylonitrile-butadienestyrene (ABS) sewer pipe, produced by single extrusion or simultaneous multiple coextrusion. This specification also covers fittings. Included are requirements and test methods for materials, dimensions, workmanship, chemical resistance, water resistance, and joint tightness. A form of marking to indicate compliance with this specification is also included.

    1.2 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

    The following precautionary caveat pertains only to the test methods portion, Section , of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.



    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D618 Practice for Conditioning Plastics for Testing

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

    D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

    D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

    D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

    D3965 Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings

    F412 Terminology Relating to Plastic Piping Systems

    F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

    Federal Standard

    Fed.Std.No.123 Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700 Robbins Ave., Philadelphia, PA 19111-5094, Attn: NPODS.

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage


    Referencing This Standard

    DOI: 10.1520/D2751-05

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM D2751-05, Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014), ASTM International, West Conshohocken, PA, 2005, www.astm.org

    Back to Top