ASTM D2680 - 01(2009)

    Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Composite Sewer Piping

    Active Standard ASTM D2680 | Developed by Subcommittee: F17.62

    Book of Standards Volume: 08.04


    Buy Standard (PDF)
    8 pages
    $42.00
    Buy Standard (Print)
    8 pages
    $42.00
    Buy Standard + Redline (PDF)
    16 pages
    $50.40

    Historical (view previous versions of standard)


    ASTM D2680

    Abstract

    This specification covers acrylonitrile-butadiene-styrene (ABS) and poly(vinyl chloride) (PVC) thermoplastic composite pipe, fittings, and a joining system for use in gravity flow, nonpressure sanitary sewer, and storm drain installations. ABS or PVC composite pipes shall consist of two concentric thermoplastic tubes integrally braced across the annulus and the resultant annular space shall be filled to provide continuous support between the inner and outer tubes. Referee and quality control tests shall be conducted in the standard laboratory atmosphere under the specified temperature and humidity conditions. The pipe shall be tested for performance requirements such as stiffness, deflection without rupture, acid conditioning, joint (solvent cement and elastomeric seal joints) tightness, and extrusion quality.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers thermoplastic composite pipe, fittings and a joining system for use in gravity flow, nonpressure sanitary sewer, and storm drain installations. The pipe and fittings are made of ABS or PVC plastic material. Recommended installation practices are referenced in Appendix X1.

    1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.3 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary information is given in 7.2.4.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D618 Practice for Conditioning Plastics for Testing

    D1084 Test Methods for Viscosity of Adhesives

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2152 Test Method for Adequacy of Fusion of Extruded Poly(Vinyl Chloride) (PVC) Pipe and Molded Fittings by Acetone Immersion

    D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

    D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

    D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2564 Specification for Solvent Cements for Poly(Vinyl Chloride) (PVC) Plastic Piping Systems

    D3138 Specification for Solvent Cements for Transition Joints Between Acrylonitrile-Butadiene-Styrene (ABS) and Poly(Vinyl Chloride) (PVC) Non-Pressure Piping Components

    D3212 Specification for Joints for Drain and Sewer Plastic Pipes Using Flexible Elastomeric Seals

    D3965 Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings

    D4396 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds for Plastic Pipe and Fittings Used in Nonpressure Applications

    F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

    F412 Terminology Relating to Plastic Piping Systems

    F477 Specification for Elastomeric Seals (Gaskets) for Joining Plastic Pipe

    F913 Specification for Thermoplastic Elastomeric Seals (Gaskets) for Joining Plastic Pipe

    Federal Standard

    Fed.Std.No.123 Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage


    ICS Code

    ICS Number Code 23.040.20 (Plastic pipes)

    UNSPSC Code

    UNSPSC Code 13111004(Acrylonitrile butadiene styrene resin); 40171517(Commercial PVC pipe)


    DOI: 10.1520/D2680-01R09

    ASTM International is a member of CrossRef.

    ASTM D2680

    Citing ASTM Standards
    Back to Top