ASTM D2661 - 11

    Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings

    Active Standard ASTM D2661 | Developed by Subcommittee: F17.63

    Book of Standards Volume: 08.04


      Format Pages Price  
    PDF 9 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 9 $43.00   ADD TO CART
    Standard + Redline PDF Bundle 18 $51.60   ADD TO CART


    Abstract

    This specification covers acrylonitrile-butadiene-styrene (ABS) schedule 40 plastic drain, waste, and vent pipe and fittings. ABS plastic which does not meet the material requirements is excluded. ABS plastic shall conform to the minimum content requirements of polymers or polymer blends and shall compose of acrylonitrile, butadiene, styrene or substituted styrene or both, and other monomeric or polymeric components. Pipe and fittings shall be homogenous and free of defects. Other requirements include dimensions, tolerances, stiffness, flattening, impact resistance, and bond strength. Sampling, conditioning, product marking, and quality shall conform to the requirements of this specification.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers fittings and single and coextruded acrylonitrile-butadiene-styrene (ABS) plastic drain, waste, and vent pipe (DWV) made to Schedule 40 iron pipe sizes (IPS). Plastic which does not meet the material requirements specified in Section 5 is excluded from single layer and all coextruded layers.

    1.2 Specification for fittings for use with pipe meeting the requirements of this specification are given in Annex A1.

    1.3 Acrylonitrile-butadiene-styrene plastic, which does not meet the definition of virgin ABS plastic as given in 3.2.2, is excluded, as performance of plastic other than those defined as virgin was not determined. ABS rework plastic, which meets the requirements of rework plastic as given in 5.3, is acceptable.

    1.4 Reprocessed plastic or recycled plastic as defined in Terminology D883 is excluded.

    1.5 Recommendations for storage, joining, and installation are provided in Appendix X1, Appendix X2, and Appendix X3, respectively.

    1.6 The text of this specification references notes, footnotes, and appendixes which provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the specification.

    1.7 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D618 Practice for Conditioning Plastics for Testing

    D883 Terminology Relating to Plastics

    D1600 Terminology for Abbreviated Terms Relating to Plastics

    D1898 Practice for Sampling of Plastics

    D2122 Test Method for Determining Dimensions of Thermoplastic Pipe and Fittings

    D2235 Specification for Solvent Cement for Acrylonitrile-Butadiene-Styrene (ABS) Plastic Pipe and Fittings

    D2321 Practice for Underground Installation of Thermoplastic Pipe for Sewers and Other Gravity-Flow Applications

    D2412 Test Method for Determination of External Loading Characteristics of Plastic Pipe by Parallel-Plate Loading

    D2444 Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)

    D3311 Specification for Drain, Waste, and Vent (DWV) Plastic Fittings Patterns

    D3965 Classification System and Basis for Specifications for Rigid Acrylonitrile-Butadiene-Styrene (ABS) Materials for Pipe and Fittings

    E105 Practice for Probability Sampling of Materials

    E122 Practice for Calculating Sample Size to Estimate, With Specified Precision, the Average for a Characteristic of a Lot or Process

    F402 Practice for Safe Handling of Solvent Cements, Primers, and Cleaners Used for Joining Thermoplastic Pipe and Fittings

    F412 Terminology Relating to Plastic Piping Systems

    F1498 Specification for Taper Pipe Threads 60 for Thermoplastic Pipe and Fittings

    F2135 Specification for Molded Drain, Waste, and Vent (DWV) Short-Pattern Plastic Fittings

    Federal Standard

    Fed.Std.No.123 Marking for Shipment (Civil Agencies) Available from Standardization Documents Order Desk, DODSSP, Bldg. 4, Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http://www.dodssp.daps.mil.

    Military Standard

    MIL-STD-129 Marking for Shipment and Storage


    ICS Code

    ICS Number Code 23.040.20 (Plastic pipes)

    UNSPSC Code

    UNSPSC Code 40170000(Pipe piping and pipe fittings)


    DOI: 10.1520/D2661-11

    ASTM International is a member of CrossRef.

    ASTM D2661

    Citing ASTM Standards
    Back to Top