ASTM D2058 - 03(2014)

    Standard Test Method for Durability of Finish of Zippers to Drycleaning

    Active Standard ASTM D2058 | Developed by Subcommittee: D13.54

    Book of Standards Volume: 07.01


    Buy Standard (PDF)
    2 pages
    $37.00
    Buy Standard (Print)
    2 pages
    $37.00

    Historical (view previous versions of standard)


    ASTM D2058

    Significance and Use

    5.1 Test Method D2058 is useful for determining the effect of repeated drycleaning on the appearance of the decorative coating of a zipper.

    5.2 This test method is considered satisfactory for acceptance testing of commercial shipments because the method has been used extensively in the trade for acceptance testing.

    5.2.1 If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, the test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.

    5.3 The method(s) in the standard along with those in Test Methods D2051, D2052, D2053, D2054, D2057, D2059, D2060, D2061, and D2062 are a collection of proven test methods. They can be used as aids in the evaluation of zippers without the need for a thorough knowledge of zippers. The enumerated test methods do not provide for the evaluation of all zipper properties. Besides those properties measured by means of the enumerated test methods there are other properties that may be important for the satisfactory performance of a zipper. Test methods for measuring those properties have not been published either because no practical methods have yet been developed or because a valid evaluation of the information resulting from existing unpublished methods requires an intimate and thorough knowledge of zippers.

    1. Scope

    1.1 This test method covers the determination of the durability of the enamel or other decorative coating of zippers when subjected to drycleaning.

    1.2 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    AATCC Method

    Method 86 Drycleaning: Durability of Applied Designs and Finishes Technical Manual of the American Association of Textile Chemists and Colorists, P.O. Box 12215, Research Triangle Park, NC 27709.

    ASTM Standards

    D123 Terminology Relating to Textiles

    D2050 Terminology Relating to Fasteners and Closures Used with Textiles

    D2051 Test Method for Durability of Finish of Zippers to Laundering

    D2052 Test Method for Colorfastness of Zippers to Drycleaning

    D2053 Test Method for Colorfastness of Zippers to Light

    D2054 Test Method for Colorfastness of Zipper Tapes to Crocking

    D2057 Test Method for Colorfastness of Zippers to Laundering

    D2059 Test Method for Resistance of Zippers to Salt Spray (Fog)

    D2060 Test Methods for Measuring Zipper Dimensions

    D2061 Test Methods for Strength Tests for Zippers

    D2062 Test Methods for Operability of Zippers


    ICS Code

    ICS Number Code 61.040 (Headgear. Clothing accessories. Fastening of clothing)

    UNSPSC Code

    UNSPSC Code 53141503(Zippers)


    DOI: 10.1520/D2058

    ASTM International is a member of CrossRef.

    ASTM D2058

    Citing ASTM Standards
    Back to Top