ASTM D1863 / D1863M - 05(2011)e1

    Standard Specification for Mineral Aggregate Used on Built-Up Roofs

    Active Standard ASTM D1863 / D1863M | Developed by Subcommittee: D08.03

    Book of Standards Volume: 04.04


      Format Pages Price  
    PDF Version 2 $37.00   ADD TO CART
    Print Version 2 $37.00   ADD TO CART


    Abstract

    This specification covers the standards for the quality and grading of crushed stone, crushed slag, and water-worn gravel intended for use as coarse mineral aggregate on built-up roofs. The crushed stone and gravel shall be hard, durable, opaque, and free of foreign substances. The crushed slag, on the other hand, shall be hard, air-cooled, and free of as well of any foreign particles. The specimens shall comply with the gradation and physical requirements prescribed herein and shall undergo testing which include a gradation test, moisture test, unit mass test, dust, and hardness test.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers the quality and grading of crushed stone, crushed slag, and water-worn gravel suitable for use as coarse mineral aggregate on built-up roofs.

    1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

    ^REFERENCE:

    ASTM Standards:

    C29/C29M Test Method for Bulk Density (“Unit Weight”) and Voids in Aggregate

    C33 Specification for Concrete Aggregates

    C117 Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing

    C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates

    D75 Practice for Sampling Aggregates

    D448 Classification for Sizes of Aggregate for Road and Bridge Construction

    D1864 Test Method for Moisture in Mineral Aggregate Used on Built-Up Roofs

    D1865 Test Method for Hardness of Mineral Aggregate Used on Built-Up Roofs

    E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C29/C29M Test Method for Bulk Density (Unit Weight) and Voids in Aggregate

    C33 Specification for Concrete Aggregates

    C117 Test Method for Materials Finer than 75-m (No. 200) Sieve in Mineral Aggregates by Washing

    C136 Test Method for Sieve Analysis of Fine and Coarse Aggregates

    D75 Practice for Sampling Aggregates

    D448 Classification for Sizes of Aggregate for Road and Bridge Construction

    D1864 Test Method for Moisture in Mineral Aggregate Used on Built-Up Roofs

    D1865 Test Method for Hardness of Mineral Aggregate Used on Built-Up Roofs

    E11 Specification for Woven Wire Test Sieve Cloth and Test Sieves


    ICS Code

    ICS Number Code 91.100.50 (Binders. Sealing materials)

    UNSPSC Code

    UNSPSC Code 30111800(Aggregates)


    DOI: 10.1520/D1863_D1863M-05R11E01

    ASTM International is a member of CrossRef.

    ASTM D1863 / D1863M

    Citing ASTM Standards
    Back to Top