ASTM D1777 - 96(2011)e1

    Standard Test Method for Thickness of Textile Materials

    Active Standard ASTM D1777 | Developed by Subcommittee: D13.59

    Book of Standards Volume: 07.01


      Format Pages Price  
    PDF 5 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 5 $43.00   ADD TO CART


    Significance and Use

    This test method is considered satisfactory for acceptance testing of commercial shipments since current estimates of between-laboratory precision are acceptable, and this test method is used extensively in the trade for acceptance testing.

    In case of a dispute arising from differences in reported test results when using this test method for acceptance testing of commercial shipments, the purchaser and the supplier should conduct comparative tests to determine if there is a statistical bias between their laboratories. Competent statistical assistance is recommended for the investigation of bias. As a minimum, the two parties should take a group of test specimens that are as homogeneous as possible and that are from a lot of material of the type in question. Test specimens then should be randomly assigned in equal numbers to each laboratory for testing. The average results from the two laboratories should be compared using the appropriate statistical analysis and an acceptable probability level chosen by the two parties before testing is begun. If a bias is found, either its cause must be found and corrected, or the purchaser and the supplier must agree to interpret future test results with consideration to the known bias.

    Thickness is one of the basic physical properties of textile materials. In certain industrial applications, the thickness may require rigid control within specified limits. Bulk and warmth properties of textile materials are often estimated from their thickness values, and thickness is also useful in measuring some performance characteristics, such as before and after abrasion and shrinkage.

    The thickness value of most textile materials will vary considerably depending on the pressure applied to the specimen at the time the thickness measurement is taken. In all cases, the apparent thickness varies inversely with the pressure applied. For this reason, it is essential that the pressure be specified when discussing or listing any thickness value.

    When using this test method for measuring the thickness of textile materials, the primary method for the specific material such as listed in the Referenced Document section shall take precedence over the directions described in this test method, unless specifically provided for in that test method. This test method is used in its entirety when no test method for measuring thickness is available for the specific material to be tested or unless otherwise specified in a material specification or contract order.

    1. Scope

    1.1 This test method covers the measurement of the thickness of most textile materials.

    1.2 This test method applies to most fabrics including woven fabrics, air bag fabrics, blankets, napped fabrics, knitted fabrics, layered fabrics, and pile fabrics. The fabrics may be untreated, heavily sized, coated, resin-treated, or otherwise treated. Instructions are provided for testing thickness, except as provided for in another standard such as listed in Section 2.

    1.3 The values stated in SI units are to be regarded as the standard. The values stated in inch-pound may be approximate.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D123 Terminology Relating to Textiles

    D1776 Practice for Conditioning and Testing Textiles

    D2904 Practice for Interlaboratory Testing of a Textile Test Method that Produces Normally Distributed Data

    D2906 Practice for Statements on Precision and Bias for Textiles


    ICS Code

    ICS Number Code 59.080.30 (Textile fabrics)

    UNSPSC Code

    UNSPSC Code 11161800(Synthetic fabrics)


    Referencing This Standard

    DOI: 10.1520/D1777-96R11E01

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM D1777-96(2011)e1, Standard Test Method for Thickness of Textile Materials, ASTM International, West Conshohocken, PA, 2011, www.astm.org

    Back to Top