ASTM D1458 - 13

    Standard Test Methods for Fully Cured Silicone Rubber-Coated Glass Fabric and Tapes for Electrical Insulation

    Active Standard ASTM D1458 | Developed by Subcommittee: D09.07

    Book of Standards Volume: 10.01


    Buy Standard (PDF)
    8 pages
    $42.00
    Buy Standard (Print)
    8 pages
    $42.00
    Buy Standard + Redline (PDF)
    16 pages
    $50.40

    Historical (view previous versions of standard)


    ASTM D1458

    Abstract

    These test methods cover procedures for testing fully cured silicone rubber-coated glass fabric and tapes to be used for electrical insulation. The test procedures for the following test methods are detailed: (1) breaking strength, (2) breaking strength after creasing, (3) dielectric breakdown voltage, (4) dielectric proof voltage, (5) dissipation factor and relative permittivity, (6) thermal endurance, (7) thickness, (8) thread count, (9) volume resistivity, and (10) weight. The procedures for sampling of fabric rolls, fabric sheets, tapes and strips, and test specimen preparation and conditioning are given. The test apparatus, report requirements, and precision and bias for each test are provided. The drum type gripping device and creasing apparatus for breaking strength test are illustrated. Voltage stress test shall be done for dissipation factor and relative permittivity and volume resistivity tests.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 These test methods cover procedures for testing fully cured silicone rubber-coated glass fabric and tapes to be used for electrical insulation.

    1.2 The procedures appear in the following order:

    Procedure

    Sections

    ASTM
    References

     

    Breaking Strength

     7

     D828

    Breaking Strength After Creasing

     8

     ...

    Conditioning

     5

     ...

    Dielectric Breakdown Voltage

     9

     D149, D295,
      D6054

    Dielectric Proof-Voltage

     10

     D1389

    Dissipation Factor and Relative Permittivity

    11

     D150

    Sampling

     4

     ...

    Thermal Endurance

    15

     D1830

    Thickness

     6

     D374

    Thread Count

    14

     ...

    Volume Resistivity

    12

     D257

    Weight

    13

     ...


    1.3 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

    1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. See 9.5.1 for a specific warning statement.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    D149 Test Method for Dielectric Breakdown Voltage and Dielectric Strength of Solid Electrical Insulating Materials at Commercial Power Frequencies

    D150 Test Methods for AC Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulation

    D202 Test Methods for Sampling and Testing Untreated Paper Used for Electrical Insulation

    D257 Test Methods for DC Resistance or Conductance of Insulating Materials

    D295 Test Methods for Varnished Cotton Fabrics Used for Electrical Insulation

    D374 Test Methods for Thickness of Solid Electrical Insulation

    D828 Test Method for Tensile Properties of Paper and Paperboard Using Constant-Rate-of-Elongation Apparatus

    D1389 Test Method for Proof-Voltage Testing of Thin Solid Electrical Insulating Materials

    D1711 Terminology Relating to Electrical Insulation

    D1830 Test Method for Thermal Endurance of Flexible Sheet Materials Used for Electrical Insulation by the Curved Electrode Method

    D5032 Practice for Maintaining Constant Relative Humidity by Means of Aqueous Glycerin Solutions

    D6054 Practice for Conditioning Electrical Insulating Materials for Testing

    E104 Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions


    ICS Code

    ICS Number Code 29.035.30 (Glass and ceramic insulating materials)

    UNSPSC Code

    UNSPSC Code 13100000(Rubber and elastomers)


    DOI: 10.1520/D1458

    ASTM International is a member of CrossRef.

    ASTM D1458

    Citing ASTM Standards
    Back to Top