ASTM D1050 - 05(2011)

    Standard Specification for Rubber Insulating Line Hose

    Active Standard ASTM D1050 | Developed by Subcommittee: F18.25

    Book of Standards Volume: 10.03


      Format Pages Price  
    PDF 7 $42.00   ADD TO CART
    Hardcopy (shipping and handling) 7 $42.00   ADD TO CART


    Abstract

    This specification covers acceptance testing of rubber insulating line hose for use as a portable protective device for protection of workers from accidental contact with live electrical conductors. Two types of line hose are provided and are designated as Type I, non-resistant to ozone, and Type II and Type III, resistant to ozone. Five classes of line hose, differing in electrical characteristics, are provided and are designated as Class 0, Class 1, Class 2, Class 3, and Class 4. Four styles of line hose, differing in design characteristics, are provided and are designated as Style A, Style B, Style C, and Style D. The line hose shall be constructed in four styles: straight style, connector-end style, extended-lip style, and connectorend extended-lip style. The line hose shall be formed with an interlocking lip of sufficient length to prevent the device from being dislodged accidentally from the conductor it covers. The interlocking lip shall be closely adjacent to the inside surface contour of the outer wall. The depth of adapter end of connector-end style line hose shall be not less than a certain value, and its inside diameter shall be such that it will snugly grip the end of the line hose of the same size which it joins. Each line hose shall conform to the physical requirements such as determined tensile strength, elongation, tension set, tear resistance and moisture absorption.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers acceptance testing of rubber insulating line hose for use as a portable protective device for protection of workers from accidental contact with live electrical conductors.

    1.2 Two types of line hose are provided and are designated as Type I, non-resistant to ozone, and Type II and Type III, resistant to ozone.

    1.3 Five classes of line hose, differing in electrical characteristics, are provided and are designated as Class 0, Class 1, Class 2, Class 3, and Class 4.

    1.4 Four styles of line hose, differing in design characteristics, are provided and are designated as Style A, Style B, Style C, and Style D.

    The following precautionary caveat pertains only to the test method portion, Sections 16, 17, 18, 19, of this specification:This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. For specific precautionary statements, see 18.1.1.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    Federal Specification

    PPP-B-636 Box, Shipping, Filterboard

    ANSI Standards

    C84.1 Electric Power Systems and Equipment-Voltage Ratings

    ASTM Standards

    D297 Test Methods for Rubber Products--Chemical Analysis

    D412 Test Methods for Vulcanized Rubber and Thermoplastic Elastomers--Tension

    D570 Test Method for Water Absorption of Plastics

    D573 Test Method for Rubber--Deterioration in an Air Oven

    D624 Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers

    D2865 Practice for Calibration of Standards and Equipment for Electrical Insulating Materials Testing

    F819 Terminology Relating to Electrical Protective Equipment for Workers


    ICS Code

    ICS Number Code 23.040.70 (Hoses and hose assemblies)

    UNSPSC Code

    UNSPSC Code 39121728(Insulating tube); 40142000(Hoses)


    DOI: 10.1520/D1050-05R11

    ASTM International is a member of CrossRef.

    ASTM D1050

    Citing ASTM Standards
    Back to Top