ASTM C1628 - 11

    Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe, Using Rubber Gaskets

    Active Standard ASTM C1628 | Developed by Subcommittee: C13.08

    Book of Standards Volume: 04.05


      Format Pages Price  
    PDF 7 $43.00   ADD TO CART
    Hardcopy (shipping and handling) 7 $43.00   ADD TO CART
    Standard + Redline PDF Bundle 14 $51.60   ADD TO CART


    Abstract

    This specification covers flexible leak resistant joints for concrete gravity flow sewer pipes using rubber gaskets for sealing the joints, where measurable or defined infiltration or exfiltration is a factor of the design. The gasket shall be fabricated from a rubber compound, the basic polymer of which shall be natural rubber, synthetic rubber, or a blend of both. Gaskets shall be manufactured in the specified design sizes and dimensions, conforming to both circular cross-section or "O-ring" gaskets, and non-circular cross-sections or "profile" gaskets. The joints shall also be made to meet design requirements as to confined circular cross-section and non-circular cross-section gasket joint designs. Volume, non-circular shape stretch height, and length of the manufactured gaskets shall be determined, while, the joints shall be evaluated according to their performances in hydrostatic and structural tests. The finished products shall be handled, stored, inspected, and marked appropriately.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers flexible leak resistant joints for concrete gravity flow sewer pipe using rubber gaskets for sealing the joints, where measurable or defined infiltration or exfiltration is a factor of the design. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specifications C14, C76, C655, C985, and C1417, provided that, if there is conflict in permissible variations in dimension, the requirements of this specification shall govern for joints.

    Note 1—Infiltration or exfiltration quantities for an installed pipeline are dependent upon many factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system. This specification covers the design, material, and performance of the rubber gasket joint only. Joints covered by this specification are for hydrostatic pressures up to 13 psi without leakage, when plant tested in accordance with Section 10.

    1.2 The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

    1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C14 Specification for Nonreinforced Concrete Sewer, Storm Drain, and Culvert Pipe

    C76 Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

    C497 Test Methods for Concrete Pipe, Manhole Sections, or Tile

    C655 Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe

    C822 Terminology Relating to Concrete Pipe and Related Products

    C985 Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe

    C1417 Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design

    C1619 Specification for Elastomeric Seals for Joining Concrete Structures


    ICS Code

    ICS Number Code 93.030 (External sewerage systems)

    UNSPSC Code

    UNSPSC Code 40170000(Pipe piping and pipe fittings)


    Referencing This Standard

    DOI: 10.1520/C1628-11

    ASTM International is a member of CrossRef.

    Citation Format

    ASTM C1628-11, Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe, Using Rubber Gaskets, ASTM International, West Conshohocken, PA, 2011, www.astm.org

    Back to Top