ASTM C1328 / C1328M - 12

    Standard Specification for Plastic (Stucco) Cement

    Active Standard ASTM C1328 / C1328M | Developed by Subcommittee: C01.11

    Book of Standards Volume: 04.01


    Buy Standard (PDF)
    4 pages
    $37.00
    Buy Standard (Print)
    4 pages
    $37.00
    Buy Standard + Redline (PDF)
    8 pages
    $44.40

    Historical (view previous versions of standard)


    ASTM C1328 / C1328M

    Abstract

    This specification covers plastic cements for use in Portland cement-based plasters for exterior (stucco) and interior applications. All the materials should be tested and conform to the required values of fineness, autoclave expansion, time of setting, compressive strength, air content of mortar, and water retention. The cement should be stored in a way that permits easy access and inside a suitable weathertight building.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers two types of plastic cement for use in portland cement-based plasters for exterior (stucco) and interior application.

    1.2 UnitsThe values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units shall be obtained by measurement in SI units or by appropriate conversion, using the Rules for Conversion and Rounding given in Standard , of measurements made in other units. Values are stated in only SI units when inch-pound units are not used in practice.

    1.3 The text of this standard refers to notes and footnotes that provide explanatory material. These notes and footnotes (excluding those in tables and figures) shall not be considered as requirements of the standard.

    1.4 The following safety hazards caveat pertains only to Sections 14 and 15. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. (WarningFresh hydraulic cementitious mixtures are caustic and may cause chemical burns to skin and tissue upon prolonged exposure.)


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    C109/C109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)

    C151 Test Method for Autoclave Expansion of Hydraulic Cement

    C183 Practice for Sampling and the Amount of Testing of Hydraulic Cement

    C185 Test Method for Air Content of Hydraulic Cement Mortar

    C187 Test Method for Amount of Water Required for Normal Consistency of Hydraulic Cement Paste

    C188 Test Method for Density of Hydraulic Cement

    C219 Terminology Relating to Hydraulic Cement

    C266 Test Method for Time of Setting of Hydraulic-Cement Paste by Gillmore Needles

    C305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency

    C430 Test Method for Fineness of Hydraulic Cement by the 45-m (No. 325) Sieve

    C511 Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes

    C778 Specification for Sand

    C926 Specification for Application of Portland Cement-Based Plaster

    C1506 Test Method for Water Retention of Hydraulic Cement-Based Mortars and Plasters


    ICS Code

    ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

    UNSPSC Code

    UNSPSC Code 30111601(Cement)


    DOI: 10.1520/C1328_C1328M-12

    ASTM International is a member of CrossRef.

    ASTM C1328 / C1328M

    Citing ASTM Standards
    Back to Top