ASTM C1063 - 14a

    Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement-Based Plaster

    Active Standard ASTM C1063 | Developed by Subcommittee: C11.03

    Book of Standards Volume: 04.01


    Buy Standard (PDF)
    10 pages
    $42.00
    Buy Standard (Print)
    10 pages
    $42.00
    Buy Standard + Redline (PDF)
    20 pages
    $50.40

    Historical (view previous versions of standard)


    ASTM C1063

    Abstract

    This specification covers the installation of lathing and furring to receive interior and exterior Portland cement-based plaster. The following materials shall be used: metal plaster basesexpanded metal lath and wire laths; accessoriessteel, PVC plastic, zinc alloy, and cornerite; channelsexternal corner reinforcement and foundation weep screed; wire; rod and strap hangers; clips; fastenersnails and screws. Hangers and cold-rolled channel main runner shall conform to the allowable spacing and spans, respectively. The following methods are discussed: installation of hangers for suspended ceilings under wood constructions, attachment of hangers to main runners, installation of main runners, installation of cross furring, metal furring for walls, lapping of metal plaster bases, spacing of attachments for metal plaster bases, application of metal plaster bases, and application of accessories.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification covers the minimum requirements for lathing and furring for the application of exterior and interior portland cement-based plaster as in Specification C926 or Specification C841.

    1.2 Where a fire resistance rating is required for plastered assemblies and constructions, details of construction shall be in accordance with reports of fire tests of assemblies that have met the requirements of the fire rating imposed.

    1.3 Where a specific degree of sound control is required for plastered assemblies and constructions, details of construction shall be in accordance with official reports of tests conducted in recognized testing laboratories in accordance with the applicable requirements of Test Method E90.

    1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    A641/A641M Specification for Zinc-Coated (Galvanized) Carbon Steel Wire

    A653/A653M Specification for Steel Sheet, Zinc-Coated (Galvanized) or Zinc-Iron Alloy-Coated (Galvannealed) by the Hot-Dip Process

    B69 Specification for Rolled Zinc

    B221 Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes

    C11 Terminology Relating to Gypsum and Related Building Materials and Systems

    C841 Specification for Installation of Interior Lathing and Furring

    C847 Specification for Metal Lath

    C926 Specification for Application of Portland Cement-Based Plaster

    C933 Specification for Welded Wire Lath

    C954 Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm) in Thickness

    C1002 Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs

    C1032 Specification for Woven Wire Plaster Base

    D1784 Specification for Rigid Poly(Vinyl Chloride) (PVC) Compounds and Chlorinated Poly(Vinyl Chloride) (CPVC) Compounds

    D4216 Specification for Rigid Poly(Vinyl Chloride) (PVC) and Related PVC and Chlorinated Poly(Vinyl Chloride) (CPVC) Building Products Compounds

    E90 Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements


    ICS Code

    ICS Number Code 91.100.10 (Cement. Gypsum. Lime. Mortar)

    UNSPSC Code

    UNSPSC Code


    DOI: 10.1520/C1063

    ASTM International is a member of CrossRef.

    ASTM C1063

    Citing ASTM Standards
    Back to Top