Abstract
This specification covers heat-treated flat glass - kind HS, kind FT coated and uncoated glass used in general building construction. Glass furnished under this specification shall be of the following conditions: condition A - uncoated surfaces, condition B - spandrel glass, one surface ceramic coated, and condition C - other coated glass. Flat glass furnished under this specification shall be of the following kinds: kind HS - heat-strengthened glass shall be flat glass, either transparent or patterned, in accordance with the applicable requirements, and kind FT - fully tempered glass shall be flat glass, either transparent or patterned in accordance with the applicable requirements. All fabrication, such as cutting to overall dimensions, edgework, drilled holes, notching, grinding, sandblasting, and etching, shall be performed before strengthening or tempering and shall be as specified. Requirements for fittings and hardware shall be as specified. In heat-strengthened and fully tempered glass, a strain pattern, which is not normally visible, may become visible under certain light conditions. The support system and the amount of glass deflection for a given set of wind-load conditions must be considered for design purposes. Heat-treated flat glass cannot be cut after tempering. Heat-treated glass can be furnished with holes, notches, cutouts, and bevels. The expansion fit and porosity of the ceramic coating shall be tested to meet the requirements prescribed. Specimens for evaluation of resistance to alkali and acid shall be prepared and tested to meet the requirements prescribed.
This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.
1. Scope
1.1 This specification covers the requirements for monolithic flat heat-strengthened and fully tempered coated and uncoated glass produced on a horizontal tempering system used in general building construction and other applications.
1.2 This specification does not address bent glass, or heat-strengthened or fully tempered glass manufactured on a vertical tempering system.
1.3 The dimensional values stated in SI units are to be regarded as the standard. The units given in parentheses are for information only.
1.4 The following safety hazards caveat pertains only to the test method portion, Section 10, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
2. Referenced Documents (purchase separately) 
The documents listed below are referenced within the subject standard but are not provided as part of the standard.
ASTM Standards
C162 Terminology of Glass and Glass Products
C346 Test Method for 45-deg Specular Gloss of Ceramic Materials
C724 Test Method for Acid Resistance of Ceramic Decorations on Architectural-Type Glass
C978 Test Method for Photoelastic Determination of Residual Stress in a Transparent Glass Matrix Using a Polarizing Microscope and Optical Retardation Compensation Procedures
C1036 Specification for Flat Glass
C1203 Test Method for Quantitative Determination of Alkali Resistance of a Ceramic-Glass Enamel
C1279 Test Method for Non-Destructive Photoelastic Measurement of Edge and Surface Stresses in Annealed, Heat-Strengthened, and Fully Tempered Flat Glass
C1376 Specification for Pyrolytic and Vacuum Deposition Coatings on Flat Glass
E1300 Practice for Determining Load Resistance of Glass in Buildings
ANSI Standard
Z97.1 Safety Performance Specifications and Methods of Test for Safety Glazing Materials Used in Buildings Available from American National Standards Institute, 25 W. 43rd St., 4th Floor, New York, NY 10036, and the Accredited Standards Committee Z97 website in electronic format at www.ansiz97.com.
Keywords
edge compression; flat glass; heat-strengthened glass; heat-treated glass; surface compression; tempered glass ;
ICS Code
ICS Number Code 81.040.30 (Glass products)
DOI: 10.1520/C1048-12E01
ASTM International is a member of CrossRef.
Citing ASTM Standards
[Back to Top]
