ASTM B829 - 04A(2009)e1

    Standard Specification for General Requirements for Nickel and Nickel Alloys Seamless Pipe and Tube

    Active Standard ASTM B829 | Developed by Subcommittee: B02.07

    Book of Standards Volume: 02.04


    Buy Standard (PDF)
    6 pages
    $42.00
    Buy Standard (Print)
    6 pages
    $42.00

    Historical (view previous versions of standard)


    ASTM B829

    Abstract

    This general specification contains the mandatory requirements to the ASTM standards listed herein for seamless pipes and tubes made from nickel and nickel alloys. In case of conflict, the requirements listed in the particular product specification takes precedence over those listed here.

    This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

    1. Scope

    1.1 This specification contains various requirements that, with the exception of Sections 5 and 10, are mandatory requirements to the following ASTM nickel and nickel alloy, seamless pipe and tube specifications:

    Title of Specification

    ASTM
    Designation2

    Nickel Seamless Pipe and Tube

    B161

    Seamless Nickel and Nickel Alloy, Condenser and Heat Ex-
     changer Tubes

    B163

    Nickel-Copper Alloy (UNS N04400) Seamless Pipe and Tube

    B165

    Nickel-Chromium-Iron Alloys (UNS N06600, N06601, and
     N06690) Seamless Pipe and Tube

    B167

    Nickel-Iron-Chromium Alloy Seamless Pipe and Tube

    B407

    Nickel-Iron-Chromium-Molybdenum-Copper Alloy (UNS N08825
     and N08221) Seamless Pipe and Tube

    B423

    Nickel-Chromium-Molybdenum-Columbium Alloys (UNS
     N06625) Pipe and Tube

    B444

    Nickel-Chromium-Iron-Columbium-Molybdenum-Tungsten Alloy
     (UNS N06102) Seamless Pipe and Tube

    B445

    Nickel-Iron-Chromium-Silicon Alloys (UNS N08330 and UNS
     N08332) Seamless Pipe

    B535

    Copper-Beryllium Alloy Forgings and Extrusion

     B570

    Seamless Nickel and Nickel-Cobalt Alloy Pipe and Tube

    B622

    UNS N08028 Seamless Tubes

    B668

    UNS N08904, UNS N08925 and UNS N08926 Seamless Pipe
     and Tube

    B677

    Iron-Nickel-Chromium-Molybdenum Alloys (UNS N08366 and
     UNS N08367) Seamless Pipe and Tube

    B690

    Ni-Cr-Mo-Co-W-Fe-Si Alloy (UNS N06333) Seamless Pipe and
     Tube

    B722

    Seamless UNS N08020, UNS N08026, and UNS N08024
     Nickel-Alloy Pipe and Tube

    B729


    1.2 One or more of the test requirements of Section 5 apply only if specifically stated in the product specification or in the purchase order.

    1.3 In case of conflict between a requirement of the product specification and a requirement of this general specification, only the requirement of the product specification needs to be satisfied.

    1.4 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

    1.5 The following safety hazards caveat pertains only to the test requirements portion, Section 5, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to become familiar with all hazards including those identified in the appropriate Material Safety Data Sheet (MSDS) for this product/material as provided by the manufacturer, to establish appropriate safety and health practices, and determine the applicability of regulatory limitations prior to use.


    2. Referenced Documents (purchase separately) The documents listed below are referenced within the subject standard but are not provided as part of the standard.

    ASTM Standards

    B880 Specification for General Requirements for Chemical Check Analysis Limits for Nickel, Nickel Alloys and Cobalt Alloys

    E8/E8M Test Methods for Tension Testing of Metallic Materials

    E18 Test Methods for Rockwell Hardness of Metallic Materials

    E29 Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications

    E39 Methods for Chemical Analysis of Nickel

    E76 Test Methods for Chemical Analysis of Nickel-Copper Alloys

    E112 Test Methods for Determining Average Grain Size

    E213 Practice for Ultrasonic Testing of Metal Pipe and Tubing

    E426 Practice for Electromagnetic (Eddy-Current) Examination of Seamless and Welded Tubular Products, Titanium, Austenitic Stainless Steel and Similar Alloys

    E571 Practice for Electromagnetic (Eddy-Current) Examination of Nickel and Nickel Alloy Tubular Products

    E1473 Test Methods for Chemical Analysis of Nickel, Cobalt, and High-Temperature Alloys

    ANSI Standards

    B36.19 Stainless Steel Pipe


    ICS Code

    ICS Number Code 23.040.15 (Non-ferrous metal pipes)

    UNSPSC Code

    UNSPSC Code 11101706(Nickel)


    DOI: 10.1520/B0829-04AR09E01

    ASTM International is a member of CrossRef.

    ASTM B829

    Citing ASTM Standards
    Back to Top